Auerswald COMpact 5000 Скачать руководство пользователя | Manualshive

Страница: 232 / 932

background image

232

COMpact 5000/R - Firmware V6.6A - Installation, Operation and Configuration V05 03/2016

Voice Mail and Fax Boxes

Voice Mailbox
Configuring a Voice Mailbox

Voice Mailbox

A voice mailbox assumes the task of an answering machine. Depending on the setting, it
accepts incoming calls and stores recorded messages as audio files (*.wav).

Configuring a Voice Mailbox

Requirements:

•

Voice mail/fax function (optional, see chapter Important Information > Product Details >
Basic Assembly and Extensions)

1. Create a voice mailbox. Here, the voice mailbox is assigned a phone number and a

name. If required, an owner is assigned.

2. Configure the

Maximum recording capacity

for the voice mailbox.

3. If required, enable

Automatic clean-up

.

4. If required, configure additional properties (

Message forwarding

,

Automatic replay

of new messages

,

Remote access

,

Language of the announcements

,

E-mail

transfer

on incoming message, if memory is full or in case of failure of automatic

clean-up).

5. If required, enable

Call pick-up

for the voice mailbox and the

Groups(s)/Voice

mailbox(es)

authorisation for the owners/users under

Pick-up

(see

Subscriber

(scr.) > Properties > Authorisations

).

6. If required, select further users for the voice mailbox and enable or disable their

authorisations (

Administrate announcements and settings

).

7. If required, record the announcements proprietary of the box or save existing

announcements for the voice mailbox in the PBX.

8. If required, assign a profile to the voice mailbox.

9. Only if no profile has been assigned to the voice mailbox (default settings of the

standard profile) or if settings have been made in the profile which can be enabled by
the user (not

Profile-controlled settings

):

Configure the

Call acceptance/announcement

function for the voice mailbox.

10. If required, configure

Readiness

permanently for the voice mailbox.

«
...
230
231
232
233
234
...
»

Содержание COMpact 5000





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для COMpact 5000

Бренд: Yeastar Technology Страницы: 152

Бренд: Panasonic Страницы: 668

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды