Auerswald COMpact 5000 Скачать руководство пользователя | Manualshive

Страница: 222 / 932

background image

222

COMpact 5000/R - Firmware V6.6A - Installation, Operation and Configuration V05 03/2016

Address Books and Lists

Call Data
Configuring the Cost per Call Unit

Configuring the Cost per Call Unit

The cost per call unit are used for internal calculations and the display.

The value entered here refers to the currency entered under

Currency name

(e.g., for the

Currency name

EUR

0.0600 for 6 cents).

Note:

For Least Cost Routing (LCR), the tariff information of dial-around providers
is saved in the PBX. This data ( charge pulse interval) replace the
cost per call unit entered here for all LCR calls.

If using an analogue exchange line or a VoIP account for external calls, no
charges will be displayed.

Proceed as follows:

•

Using the configuration manager

1. Open the page

Functions > Call allowance accounts

.

2. Enter a value in the

Price per unit

entry field. Possible entries:

Configuring the Billing Factor

The billing factor indicates the value used to convert the subscriber's telephone costs.

This factor is used to multiply the charges transmitted from the network provider or the calcu-
lated charges. The telephone costs calculated in this way are used in the call data list.

Proceed as follows:

•

Separately for subscribers

•

Using the configuration manager

1. Open the page

Subscribers (scr.) > Properties > Settings

.

2. In the list field at the top, select the subscriber in question by his name or number.

Price in 00.0000 format: Specifies the cost per call unit from 0.0000 to 99.9999.

Digits and the separator

,

«
...
220
221
222
223
224
...
»

Содержание COMpact 5000





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для COMpact 5000

Бренд: Karel Страницы: 39

Бренд: Planet Страницы: 88

Бренд: ATCOM Страницы: 64

CompletePBX CXE2000

Бренд: Xorcom Страницы: 2

AastraLink RP 500

Бренд: Aastra Страницы: 16

Бренд: TransTel Communications Страницы: 15

Бренд: Platon Страницы: 33

Бренд: IPitomy Страницы: 124

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды