Auerswald COMpact 5000 Скачать руководство пользователя | Manualshive

Страница: 172 / 932

background image

172

COMpact 5000/R - Firmware V6.6A - Installation, Operation and Configuration V05 03/2016

Address Books and Lists

Address Books
Importing an Image for a Contact Person

4. Enter at least one phone number in the

Phone numbers

entry field. Possible entries:

Note:

You can neatly arrange the phone numbers with the following

characters: (, ), -, / and space. The following phone number formats are
possible: +49 5306 -1234567 (recommended) or 05306-123457 or in the
local telephone network 1234567 (not recommended when using LDAP).

5. If necessary, you can assign a different phone number type to the phone number in

the list field under

Phone numbers

. Select one of the available options.

Possible entries for custom phone number types:

6. If required, you can enter additional information, such as

Title

,

First name

,

Department

,

Position

or

Birthday

.

7. Click

Save

.

The new contact now appears in

All contacts

view and if required, is included in the

specified standard contact group(s).

Note:

You can assign the contact to one or more other contact group(s) at a

later date.

8. Repeat steps 2 to 7 to create additional contacts.

Importing an Image for a Contact Person

You can add an image for the contact person to every contact. During a call, this image can be
displayed in addition to the name.

Note:

The image file must not exceed the maximum permitted file size of 512

KB and image size of 800 x 600 pixels.

Currently, only with COMfortel 1400 IP, 2600 IP, 3200, 3500 and COMfortel
3600 IP the contact images will be displayed, provided the contact person
has called the telephone in question at least once.

Digits and characters *, #, +, (, ), -, / and space

Digits and characters *, #, +, (, ), -, / and space

«
...
170
171
172
173
174
...
»

Содержание COMpact 5000





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для COMpact 5000

Бренд: Tadiran Telecom Страницы: 544

Бренд: ATCOM Страницы: 35

Operator Box 1000 Series

Бренд: Kerio Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды