Auerswald a/b-Audiobox Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 40

Auerswald a/b-Audiobox Скачать руководство пользователя страница 10

Installation

10

a/b-Audiobox - Operation Guide - V03 10/2020

In this chapter you can find out how to connect the a/b-Audiobox to a PBX and a sound sys

-

tem. It also describes how to connect and configure the a/b switching modules (which are not

included in the scope of delivery).

Connecting a Sound System

Warning:

Touching live terminal clamps or power cables can cause life-

threatening electrical shocks.
• Disconnect the connection to the telephone connection on the PBX

before you carry out any work on the device.

• Ensure that any tools you use on live cables are sufficiently insulated.
• For the connection to the PBX, also note the safety information in the

manual for your PBX.

Warning:

Power surges, which may occur during electrical storms, can

cause life-threatening electric shocks, or damage or destroy the connected

PBX.
• Arrange for a qualified electrician to lay all the cables inside the building.
• Do not connect or disconnect power cables during an electrical storm.

Note:

For more information about the contact assignments, also refer to the

manual for your PBX.

You will find information about the connections for extending the switching

functions below.

Always install the cables for connecting to the a/b ports separately from

other power lines. This will avoid the creation of a disruptive humming noise

during the announcement.

Installation

«
...
8
9
10
11
12
...
»

Содержание a/b-Audiobox









































Отзывы:

Нет отзывов