background image

-  

INSTALLATION

 

DS170 PILOT 

MANUAL

32

9 - WARRANTY

• The tank is guaranteed for a period

 

five (5) years 

against breakage,  

starting from the date of fi rst use if the warranty form was returned to the 
manufacturer, In the absence of this form, the date of manufacture will be 
used as a reference point for the start of warranty. 
• The spare parts (see attached list) are guaranteed for a period of 

two (2) 

years

 starting from the date of fi rst use if the warranty form was returned 

to the manufacturer, In the absence of this form, the date of manufacture 
will be used as a reference point for the start of warranty. 

The appliance is guaranteed against all manufacturing defects, provided
that it was installed according to the instructions provided in this manual
and in compliance with all current rules and regulations in the country of
installation. All electrical connections should comply with the C15-100
standard. 

Under no circumstances does a defective part warrant the replacement 
of the whole appliance. 

The warranty only applies to parts which we (AUER) identify as having 
been defective at manufacture. If necessary, the part or product should 
be returned to the manufacturer, but only with prior agreement from 
our technical department. Labour, transport, and packaging costs 
are the responsibility of the user. Repairs on a device will not result in 
compensation. 

The warranty on replacement parts ends at the same time as the warranty 
of the appliance. 

The warranty only applies to the appliance and its components and 
excludes any part or installation external to the appliance: electrical parts, 
hydraulic components, etc...

The warranty will not apply in the absence of, insuffi

  cient, or improper, 

maintenance of the appliance.

It is essential to carry out regular annual maintenance on the 
appliances and on the installation to ensure sustained use and 
durability. This maintenance should be carried out by your 
installer, or by an AUER-approved technical center. In the absence 
of regular maintenance the warranty is rendered null and void.

If an appliance is presumed to be the cause of any damage, it must not be 
moved or tampered with before an expert assessment has been carried out. 

9.1 - Warranty coverage

9.2 - Limitations of warranty

9.2.1 - General information

The warranty does not apply to defects or damage caused by situations 
or events such as: 

• Misuse, abuse, negligence, improper transport or handling.
• Incorrect installation, or installation which has been carried out without 

following the instructions in the manual and user guide.

• Insuffi

  cient maintenance.

• Modifi cations or changes carried out on the appliance.
• Impacts from foreign objects, fi re, earthquakes, fl oods, lightning, ice, 

hailstones, hurricanes or any other natural disaster. 

• Movement, imbalance, collapse or settling of the ground or the 

structure where the appliance is installed.

• Any other damage which is not due to defects in the product.

The Pilot 

is not guaranteed against:

•  Variations in the colour of the appliance or damage caused by air pollution, 

exposure to chemical elements, or changes brought about by adverse 
weather conditions

• Dirt, rust, grease or stains which occur on the surface of the appliance.

9.2.2 - Cases (not limited to) for exclusion from 

warranty

9.2.2.1 - Usages

Cases (not limited) for exclusion from warranty:

• Filling with anything other than domestic cold wate from the drinking 

water network; such as rain-water, well-water, ...etc, or using domestic 
cold water which is particularly aggressive and not in compliance 
with the national regulations in eff ect in the country of use (DTU 60-1 
addendum 4 concerning hot water).

• Switching on the appliance without fi rst having fi lled it with water.

9.2.2.2 - Handling

Cases (not limited) for exclusion from warranty:

 • Any damage sustained by impacts or falls during handling after  

delivery from the factory.

  • Deterioration in the condition of the appliance after handling where 

the instructions in the manual have not been followed. 

9.2.2.3 - Installation site

Cases (not limited) for exclusion from warranty:

• Placement of the

 Pilot

 in a location where it could be subject to ice

  frost or other adverse weather conditions. 
• Not positioning the appliance in accordance with the instructions in 

the installer manual. 

• Installation of the appliance against a wall which cannot support the 

weight of the appliance when fi lled with water.

Costs incurred due to access difficulties are not the manufacturer’s 
responsibility. 

9.2.2.4 - Electrical connections

Cases (not limited) for exclusion from warranty:

  • Faulty electrical connection which does not conform to the national 

standards in eff ect. 

 • Not following the electrical connection diagrams provided in the 

installer manual. 

 • Electrical supply being signifi cantly over- or under- the required 

voltage. 

  • Not respecting the supply cable sections. 
 • Absence of, or insufficient electrical protection throughout the 

appliance (fuses / circuit breaker, grounding…).

• Damages caused after the neutralisation of the safety aquastat, or due 

to not having installed an appropriate safety aquastat for underfl oor 
heating. 

9.2.2.5 - Hydraulic connections

Cases (not limited) for exclusion from warranty:

  • Reversing the inlet/outlet connections. 
  • Water pressure over 7 bars.
  • Absence of, improper mounting of, or obstruction of pressure-relief 

valves. 

• Not installing pressure relief valves directly on the outlet for domestic 

cold water of the appliance. 

• Installing pressure relief valves which do not comply with the national 

regulations in eff ect (NF EN 1487 for France).

• Using pressure relief valves which are previously used. 
• Not respecting the plumbing of the pressure relief valves. 
• Abnormal corrosion due to improper hydraulic connections (direct 

contact between iron/copper) without a sleeve (cast iron, steel, or 
insulated). 

•  External corrosion due to piping being improperly sealed.

In no case can compensation be claimed due to damages caused by the 
absence of thermostatic mitigators. 

9.2.2.6 - Accessories

The warranty does not cover faults or defects resulting from:

• Installation of accessories which do not comply with our 

recommendations. 

• The use of accessories which do not come from the manufacturer of 

the appliance.

9.2.2.7 -  Maintenance

Cases (not limited) for exclusion from warranty:

• Not maintaining the appliance.
• Not maintaining the pressur relief valves leading to high pressures. 
• Abnormal levels of limescale on the heating elements and of the 

safety devices. 

•Not using parts issued by the manufacturer. 
•Outer casing and bodywork being subjected to any external damage. 

Содержание DS170 d









































Отзывы: