Audison Prima AP5.9 bit Скачать руководство пользователя страница 53

Страница: 53 / 59

USER’S MANUAL

AP5.9 bit /

By pressing the SEL button you can access:

- DSP Memory:

you can directly recall

the A/B memories (saved through the software)

and load them in

AP5.9 bit

- bass boost en:

by clicking on “Y”, it enables the

“Bass Boost” function. By clicking on “N”, it

disables the “Bass Boost” function

(see sec. 7.3.4.2)

- Brightness:

to adapt the DRC to the

light conditions inside the car, you can

adjust the brightness of the display and the

red ring on the buttons.

9.1

SEL BUTTON FUNCTIONS

It indicates activation of the amplifier thermal protection as temperature

reached 80 degrees Celsius. The amplifier will get back to normal functioning

when temperature decreases to 75 degrees Celsius.

It indicates activation of the amplifier thermal protection due to

overloaded outputs.

It indicates activation of amplifier thermal protection due to battery voltage

exceeding 16 VDC.

It indicates an internal fault. You should contact an authorized Audison

service centre.

9.2

OPERATIONAL ERROR MESSAGES

PRESS

Содержание Prima AP5.9 bit




























































Результаты поиска

Содержание Prima AP5.9 bit

Отзывы:

Бренды по названию

Популярные бренды

Audison Prima AP5.9 bit, Руководство пользователя

Результаты поиска

Содержание Prima AP5.9 bit

Отзывы:

Бренды по названию

Популярные бренды