manualshive.com logo in svg

Audison Prima AP5.9 bit, Руководство пользователя

Поделиться
Скачать
Audison Prima AP5.9 bit Скачать руководство пользователя страница 44

USER’S MANUAL

44

AP5.9 bit /

6. Filter slope

  - Hi-P Slope 

12/24 dB/Oct. (Linkwitz) 6/12/18/24dB/Oct (Butterworth)

  - Lo-P Slope 

12/24 dB/Oct. (Linkwitz) 6/12/18/24 dB/Oct (Butterworth)

    When starting the AP5.9 bit software, it offers Linkwitz with 12 dB/Oct. 

   slope.

 E.g.: 

If you select Band Pass as the filter type, the same slope will be 

   

applied to both the hi-pass and low-pass as the default slope, but  

   

they can also be unbound.

  The crossover filter response related to the selected channel is displayed graphically by a yellow curve, as shown 

  in the examples below.

 

 

E.g.

 Band Pass

Crossover Frequency 80 - 2000 Hz @ 12 dB Oct.

Crossover Frequency 80 Hz @ 6 dB Oct. Hi-pass

 

2000 Hz @ 24 dB Oct. Low-pass

Crossover Frequency  80 - 2000 Hz @ 24 dB Oct.

Crossover Frequency 80 Hz @ 24 dB Oct. Hi-pass

 

2000 Hz @ 6 dB Oct. Low-pass

This setting is based on an automatic system that calculates the time 

needed for the sound to get from the speaker to the listener's ear.

Preliminary remarks

Sound moves through the air at a speed of 343 m/sec (1.125 ft/sec.) at 

a temperature of 20° C (68° F). If you know the distance from the sound 

emission point, you can then calculate the time the sound takes to get 

to the listener’s ear.

If you set the distances of the different speakers, 

AP5.9 bit

 will 

automatically change them into time (ms - milliseconds).  It does not 

assign a delay (0.0 ms) to the farthest speaker (usually the Subwoofer) 

and progressively growing delays as much as the other speakers get 

closer to the listening point, in order for all the emission points to reach 

the listening point at the same time.

SET DISTANCE

Lets you set the distance between the speaker and the listening point. Choose cm (centimeters) or in (inches).

The "Set Distance" boxes can be set using the cursors.

DELAY ms/default

 

Displays the time in ms (milliseconds) calculated according to the distance.

DELAY ms/fine set 

AP5.9 bit

 time delay calculation system also lets you perform manual fine tuning.

7.3.11 

SET DISTANCE AND DELAY

11

7

Содержание Prima AP5.9 bit




























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды