Audison bit Tune Скачать руководство пользователя страница 94

Страница: 94 / 100

USER’S MANUAL / bit Tune /

If, after an unsuccessful firmware upgrade, you want to update the bit Tune, proceed as follows:

Connect the bit Tune to the USB port of your PC.

Disconnect all audio inputs of the bit Tune.

Turn on the bit Tune.

Start the PC software for the bit Tune and select the

RESCUE MODE

9.6

“RESCUE MODE UPGRADE MODE ON” FIRMWARE UPGRADE

Before starting the update of the bit Tune, the program provides the

following warnings:

Do not disconnect the bit Tune from the PC.

Do not disconnect the bit Tune from power supply.

Temporarily disable the automatic Stand-by in your PC.

Temporarily disable the Screen Saver in your PC.

Close any other open application.

Temporarily disable anti-virus and anti-spyware softwares

Once the OK is given, start the Firmware update of the processor.

This process takes from 30 seconds to 1 minute and its correct

progress will be indicated by the green bar.

The successful update is indicated by the message window.

Turn the

bit Tune

off and back on.

10.

Repeat the

HSM

microphone calibration

(see sect. 7.2)

WARNING:

The procedure to update the bit Tune firmware can be tricky. It is of utmost importance that it is

performed in the best possible conditions: if the operation is initiated but prematurely

interrupted (e.g. locked computer, power failure of the bit Tune, accidental disconnection of the USB

cable during the update), you may need to reprogram the bit Tune in “Rescue Mode”. In extreme

cases, contact our Customer Service to have your bit Tune reprogrammed.

WARNING:

During the upgrade, the progress of the bar may stop for a few seconds.

Do not interrupt the process in any way.

Содержание bit Tune





































































































Результаты поиска

Содержание bit Tune

Отзывы:

Бренды по названию

Популярные бренды

Audison bit Tune, Руководство пользователя

Результаты поиска

Содержание bit Tune

Отзывы:

Бренды по названию

Популярные бренды