Audiovox AA-RS5CS Скачать руководство пользователя страница 1

Страница: 1 / 16

Kit Contents

AA-RS5 Control Module

(2) - 2 Button High Frequency Transmitters

(1) - 3 Channel Code Learning Receiver

(1) - Multi Pin Input/Output Harness

(1) - Six Pin Power Harness

(1) - Two Pin I/O Harness Factory Alarm By-Pass & Diesel Wait To Start Input

(1) - 2 Pin Door Lock Harness

(2) - 30 Amp In-line Fuse Holders With Fuses

(1) - Control Switch

(1) - Programming Switch

(1) - Ring Terminal

(4) - 1/2" Long Screws

(1) - Pin Switch

(1) - Remote Start Warning Label

(1) - Literature Package

Model AA-RS5CS

Installation Manual

3 Channel Remote Start / Keyless Entry System

Installation Instructions

This Unit Is Intended For Installation In Vehicles With

12 Volt Negative Ground Electrical Systems,

Gasoline or Diesel With True Tach Reference

And Automatic Transmissions Only.

Содержание AA-RS5CS

















Результаты поиска

Содержание AA-RS5CS

Отзывы:

Похожие инструкции для AA-RS5CS

Бренды по названию

Популярные бренды

Audiovox AA-RS5CS, Руководство по установке

Результаты поиска

Содержание AA-RS5CS

Отзывы:

Похожие инструкции для AA-RS5CS

Бренды по названию

Популярные бренды