AudioCodes mediapack MP-500 Скачать руководство пользователя страница 376 | Manualshive

Страница: 376 / 574

background image

SIP User's Manual

376

Document #: LTRT-12801

MP-500

MSBG

6.8.6

Call Transfer Parameters

The call transfer parameters are described in the table below.

Table

6-35: Call Transfer Parameters

Parameter

Description

Web/EMS: Enable Transfer

[EnableTransfer]

Determines whether call transfer is enabled.

[0]

Disable = Disable the call transfer service.

[1]

Enable = Enable the call transfer service (using

REFER)(default).

If the transfer service is enabled, the user can activate
Transfer using hook-flash signaling. If this service is enabled,
the remote party performs the call transfer.

Notes:

To use call transfer, the devices at both ends must support
this option.

To use call transfer, set the parameter EnableHold to 1.

Web: Transfer Prefix
EMS: Logical Prefix For Transferred
Call

[xferPrefix]

Defines the string that is added as a prefix to the
transferred/forwarded called number when the REFER/3xx
message is received.

Notes:

The number manipulation rules apply to the user part of
the REFER-TO/Contact URI before it is sent in the INVITE
message.

This parameter can be used to apply different
manipulation rules to differentiate transferred/forwarded
number from the originally dialed number.

Web: Transfer Prefix IP 2 Tel

[XferPrefixIP2Tel]

Defines the prefix that is added to the destination number
received in the SIP Refer-to header (for IP-to-Tel calls). This
parameter is applicable to FXO Blind Transfer modes
(LineTransferMode = 1, 2 or 3 ).
The valid range is a string of up to 9 characters. The default is
an empty string.

Web/EMS: Enable Semi-Attended
Transfer

[EnableSemiAttendedTransfer]

Determines the device behavior when Transfer is initiated
while in Alerting state.

[0]

Disable = Send REFER with Replaces (default).

[1]

Enable = Send CANCEL, and after a 487 response is

received, send REFER without Replaces.

EMS: Blind Transfer Add Prefix

[KeyBlindTransferAddPrefix]

Determines whether the device adds the Blind Transfer code
(KeyBlindTransfer) to the dialed destination number.

[0]

Disable (default).

[1]

Enable.

Note:

This parameter is applicable to FXO and FXS

interfaces.

«
...
374
375
376
377
378
...
»

Содержание mediapack MP-500































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для mediapack MP-500

Бренд: Star-net Страницы: 31

Бренд: Dinstar Страницы: 41

UNIGATE IC - Powerlink

Бренд: DEUTSCHMANN AUTOMATION Страницы: 50

BridgeX BX5020 GT Series

Бренд: Mellanox Technologies Страницы: 64

Бренд: B meters Страницы: 29

DRY CONTACT GATEWAY SDG-01

Бренд: Sinclair Страницы: 20

Бренд: Ubee Страницы: 6

Бренд: SharkRF Страницы: 131

Бренд: Telecom FM Страницы: 79

Бренд: 2Wire Страницы: 131

Бренд: ZyXEL Communications Страницы: 35

Бренд: ZyXEL Communications Страницы: 56

MediaAccess TG789vn

Бренд: Technicolor Страницы: 128

Бренд: Lauda Страницы: 24

Бренд: IBM Страницы: 20

bigpond velocity

Бренд: Telstra Страницы: 13

Бренд: IDTECK Страницы: 71

Бренд: Juniper Страницы: 198

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды