AudioCodes mediapack MP-500 Скачать руководство пользователя страница 297 | Manualshive

Страница: 297 / 574

background image

Version 5.8

297

October 2009

SIP User's Manual

6. Configuration Parameters Reference

6.1.5

NAT Parameters

The Network Address Translation (NAT) parameters are described in the table below.

Table

6-5: NAT Parameters

Parameter

Description

EMS: Binding Life Time

[NATBindingDefaultTimeout]

Defines the default NAT binding lifetime in seconds. STUN
refreshes the binding information after this time expires.
The valid range is 0 to 2,592,000. The default value is 30.

Note:

For this parameter to take effect, a device reset is required.

Web: NAT IP Address
EMS: Static NAT IP Address

[StaticNatIP]

Global (public) IP address of the device to enable static Network
Address Translation (NAT) between the device and the Internet.

Note:

For this parameter to take effect, a device reset is required.

EMS: Disable NAT

[DisableNAT]

Enables / disables the Network Address Translation (NAT)
mechanism.

[0]

= Enabled.

[1]

= Disabled (default).

Note:

The compare operation that is performed on the IP address is

enabled by default and is controlled by the parameter
EnableIPAddrTranslation. The compare operation that is performed
on the UDP port is disabled by default and is controlled by the
parameter EnableUDPPortTranslation.

[EnableIPAddrTranslation]

Enables IP address translation for RTP, RTCP, and T.38 packets.

[0]

= Disable IP address translation.

[1]

= Enable IP address translation (default).

When enabled, the device compares the source IP address of the
first incoming packet to the remote IP address stated in the opening
of the channel. If the two IP addresses don't match, the NAT
mechanism is activated. Consequently, the remote IP address of
the outgoing stream is replaced by the source IP address of the first
incoming packet.

Note:

The NAT mechanism must be enabled for this parameter to

take effect (i.e., the parameter DisableNAT is set to 0).

[EnableUDPPortTranslation]

[0]

= Disable UDP port translation (default).

[1]

= Enable UDP port translation.

When enabled, the device compares the source UDP port of the
first incoming packet, to the remote UDP port stated in the opening
of the channel. If the two UDP ports don't match, the NAT
mechanism is activated. Consequently, the remote UDP port of the
outgoing stream is replaced by the source UDP port of the first
incoming packet.

Notes:

For this parameter to take effect, a device reset is required.

The NAT mechanism and the IP address translation must be
enabled for this parameter to take effect (i.e., DisableNAT = 0,
EnableIpAddrTranslation = 1).

«
...
295
296
297
298
299
...
»

Содержание mediapack MP-500































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для mediapack MP-500

Бренд: FACTBIRD Страницы: 2

Бренд: ADTRAN Страницы: 5

Бренд: Rath Страницы: 2

Бренд: Naviecare Страницы: 9

Бренд: Veratron Страницы: 79

Бренд: Epygi Страницы: 55

Бренд: ECKELMANN Страницы: 34

Бренд: Velleman Страницы: 84

LAN ECO Comfort

Бренд: SiKom Страницы: 2

Бренд: ViewSonic Страницы: 65

Бренд: tiko Energy Solutions Страницы: 40

Бренд: Planet Страницы: 146

Бренд: ZyXEL Communications Страницы: 2

Бренд: ZyXEL Communications Страницы: 2

Бренд: ZyXEL Communications Страницы: 68

Бренд: Milesight Страницы: 23

Бренд: Yacht Devices Страницы: 52

Бренд: IDTECK Страницы: 71

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды