manualshive.com logo in svg

AudioCodes Mediant 500 E-SBC, Руководство пользователя

Аудиокоды Mediant 500 E-SBC - надежное и мощное устройство для управления сессиями связи. Получите бесплатное руководство пользователя на manualshive.com, чтобы ознакомиться с функциями и настройками этого продукта. Скачайте его сейчас и начните эксплуатацию в полную силу.

Поделиться
Скачать
background image

User's Manual 

 

24. Routing 

Version 6.8 

401 

Mediant 500 E-SBC 

The steps for configuring alternative Tel-to-IP routing based on IP connectivity are 
summarized below. 

 

To configure alternative Tel-to-IP routing based on IP connectivity: 

1. 

In the Outbound IP Routing table, add alternative Tel-to-IP  routing rules for specific 
calls. 

2. 

In the Routing General Parameters page (

Configuration

 tab > 

VoIP

 menu > 

GW and 

IP to IP 

> 

Routing

 >

 General Parameters

), do the following: 

a. 

Enable alternative routing based on IP connectivity, by setting the 'Enable Alt 
Routing Tel to IP AltRouting' (Tel2IPEnable) parameter to 

Enable

. 

b. 

Configure the IP connectivity reason for triggering alternative routing, by setting 
the 'Alt Routing Tel to IP Mode' parameter (AltRoutingTel2IPMode) to one of the 
following: 

♦

 

SIP OPTIONS failure 

♦

 

Poor QoS 

♦

 

SIP OPTIONS failure, poor QoS, or unresolved DNS 

 

24.5.2  Alternative Routing Based on SIP Responses 

The device can perform alternative routing based on the received SIP response code (i.e., 
4xx, 5xx, 6xx, or 8xx). If you have configured this response code in the Reasons for Tel-to-
IP Alternative Routing table, the device attempts to re-route the call to an alternative 
destination, if configured. You can configure up to 10 SIP response codes in the Reasons 
for Tel-to-IP Alternative Routing table. 

Typically, the device performs alternative routing when there is no response at all to an 
INVITE message. This is done after a user-defined number of INVITE re-transmissions, 
configured by the SIPMaxRtx parameter. In such a scenario, the device issues itself the 
SIP response code 408 (Request Timeout). You can also configure the device to perform 
alternative routing for the following proprietary response codes that are issued by the 
device itself: 

 

805 IP Profile Call Limit:

 The device generates this response code when Call 

Admission Control (CAC) limits are exceeded for an IP Group. The CAC rules are 
configured in the IP Profile table (see ''Configuring IP Profiles'' on page 

304

). When 

this occurs, the device sends a SIP 480 (Temporarily Unavailable) response to the 
SIP entity. 

 

806 Media Limits Exceeded: 

The device generates this response code when the call 

is terminated due to crossed thresholds of QoE metrics such as MOS, packet delay, 
and packet loss (configured in the Quality of Experience Profile table) and/or media 
bandwidth (configured in the Bandwidth profile table). When this occurs, the device 
sends a SIP 480 (Temporarily Unavailable) response to the SIP entity. This is 
configured by 1) assigning an IP Group a QoE and/or Bandwidth profile that rejects 
calls if the threshold is crossed, 2) configuring 806 in the Reasons for Tel-to-IP 
Alternative Routing table and 3) configuring an alternative routing rule. 

Depending on configuration, the alternative routing is done using one of the following 
configuration entities: 

 

Outbound IP Routing Rules:

 You configure alternative routing rules for a specific 

routing rule in the Outbound IP Routing table. If the destination of the "main" routing 
rule is unavailable, the device searches the table for the next matching rule (e.g., 
destination phone number), and if available attempts to re-route the call to the IP 
destination configured for this alternative routing rule. For more information on 
configuring alternative Tel-to-IP routing rules, see ''Configuring Outbound IP Routing 
Table'' on page 

385. 

The table below shows an example of alternative routing where 

the device uses the first available alternative routing rule to re-route the initial, 
unsuccessful Tel-to-IP call destination: 

Содержание Mediant 500 E-SBC

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Mediant 500 E-SBC

Kärcher SRD Manual preview
SRD
Бренд: Kärcher Страницы: 7
Mellanox Technologies BridgeX BX5020 GT Series User Manual preview
BridgeX BX5020 GT Series
Бренд: Mellanox Technologies Страницы: 64
Alcatel-Lucent 7549 MGW Specifications preview
7549 MGW
Бренд: Alcatel-Lucent Страницы: 2
Infranet Technologies M2M CONTROL CX660 Technical Manual preview
M2M CONTROL CX660
Бренд: Infranet Technologies Страницы: 44
SpectraLink NetLink Wireless Telephone Setup And Administration Manual preview
NetLink Wireless Telephone
Бренд: SpectraLink Страницы: 30
Kiloview RMG-300 Quick Start Manual preview
RMG-300
Бренд: Kiloview Страницы: 11
Dr. Neuhaus TAINY IQ-LTE User Manual preview
TAINY IQ-LTE
Бренд: Dr. Neuhaus Страницы: 147
ViewSonic VC10 User Manual preview
VC10
Бренд: ViewSonic Страницы: 39
Endress+Hauser FieldGate SWG50 Operating Instructions Manual preview
FieldGate SWG50
Бренд: Endress+Hauser Страницы: 48
Planet Networking & Communication WIPG-300H User Manual preview
WIPG-300H
Бренд: Planet Networking & Communication Страницы: 77
ICPDAS GW-7472 Quick Start Manual preview
GW-7472
Бренд: ICPDAS Страницы: 7
AirLive IGR-2500 User Manual preview
IGR-2500
Бренд: AirLive Страницы: 81
AirLive IGR-1500 Quick Start Manual preview
IGR-1500
Бренд: AirLive Страницы: 82
EuroTech Communication GSM gateway User Manual preview
GSM gateway
Бренд: EuroTech Communication Страницы: 42
Arris Buckeye User Manual preview
Buckeye
Бренд: Arris Страницы: 116
Avaya S8700 Series Maintenance Manual preview
S8700 Series
Бренд: Avaya Страницы: 2618
US Robotics 9108 Quick Installation Manual preview
9108
Бренд: US Robotics Страницы: 136
Peripheral Electronics PGHGM5 Owner'S Manual preview
PGHGM5
Бренд: Peripheral Electronics Страницы: 16

Бренды по названию

Популярные бренды

Загрузить еще бренды