AudioCodes IPmedia 3000 Скачать руководство пользователя страница 62 | Manualshive

Страница: 62 / 90

background image

Installation Manual

62

Document #: LTRT-94704

Mediant 3000 & IPmedia 3000

Table

3-7: Alarm Terminal Block Pin Details

Pin

Pin

Description

1 - Common

2 – Normally Open (N.O)

“CRT” (Critical Alarm)

3 - Common

4 – N.O.

“MJR” (Major Alarm)

5 - Common

6 – N.O.

“MNR” (Minor Alarm)

7 – Alarm In

8 – GND

“IN” (User Alarm In)

It is recommended to provide a dual-redundant solution by wiring the two PEMs' alarm
terminal blocks to the alarm device, as shown in the figure below:

Figure

3-16: Normal Logic Alarm Connection (Redundancy Scheme)

3.3.6

Connecting the RS-232 Port to a PC

For RS-232 interface, a crossover RS-232 cable adapter (of approximately two meters) is
supplied. This cable adapter provides a 3-pin connector for connecting to the 6310/8410
blade's RS-232 port (located on the front panel) and a DB-9 connector (on the other end of
the cable) for the COM1 or COM2 RS-232 communication port on your PC.

¾

To connect the device's RS-232 port to your PC:

1.

Plug the RS-232 cable adapter's 3-pin connector into the RS-232 port (labeled

1010

),

located on the blade's front panel.

2.

Connect the DB-9 female connector (on the other end of the RS-232 cable adapter) to
your PC's COM1 or COM2 port.

Figure

3-17: RS-232 Cable Adapter (Supplied)

Note:

The RS-232 port is not intended for permanent connection.

«
...
60
61
62
63
64
...
»

Содержание IPmedia 3000



























































































Отзывы:

Нет отзывов

Похожие инструкции для IPmedia 3000

Бренд: Yeastar Technology Страницы: 15

Бренд: McQuay Страницы: 52

Бренд: TRBOnet Страницы: 33

Бренд: David Clark Страницы: 11

OFFICE CONNECT CABLE/DSL SECURE GATEWAY...

Бренд: 3Com Страницы: 102

Бренд: Profibus Страницы: 42

Бренд: ABB Страницы: 111

Бренд: ABB Страницы: 72

MicroSCADA Pro SYS 600C

Бренд: ABB Страницы: 42

Ability ATT-VZN SIM card ready gateway

Бренд: ABB Страницы: 16

Бренд: ABB Страницы: 41

Бренд: ABB Страницы: 280

Бренд: ABB Страницы: 16

lpnGate LoRaWAN

Бренд: LPN Plant Страницы: 20

WPG-150 - Wireless Video Extender

Бренд: ViewSonic Страницы: 3

Бренд: Afar Страницы: 75

Бренд: Wildix Страницы: 11

Бренд: Zycoo Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды