Audio Technica AT-LPW30TK Скачать руководство пользователя страница 3

2

Safety precautions

Important information

Warning:

• To prevent fire or shock hazard, do not expose this apparatus to rain 

or moisture.

Caution:

• Do not expose this apparatus to drips or splashes.
• To avoid electric shock, do not open the cabinet.
• Refer servicing to qualified personnel only.
• Do not expose this apparatus to excessive heat such as sunshine, fire 

or the like.

• Do not subject this apparatus to strong impact.
• This apparatus should be located close enough to the AC outlet so 

that you can easily grasp AC adapter at any time.

• In case of emergency, disconnect the AC adapter quickly.
• Do not place any objects filled with liquids, such as vases, on this 

apparatus.

• To prevent fire, do not place any open flame sources (such as lighted 

candles) on this apparatus.

• Do not install this apparatus in a confined space such as a bookcase 

or similar unit.

• Install this apparatus only in the place where ventilation is good.
• The rating label is put on the bottom of this apparatus.

For customers in the USA

FCC Notice

Warning:

This device complies with Part 15 of the FCC Rules. Operation is 
subject to the following two conditions: (1) This device may not cause 
harmful interference, and (2) this device must accept any interference 
received, including interference that may cause undesired operation.

Caution:

You are cautioned that any changes or modifications not expressly 
approved in this manual could void your authority to operate this 
equipment.
Note: This equipment has been tested and found to comply with 
the limits for a Class B digital device, pursuant to part 15 of the FCC 
Rules. These limits are designed to provide reasonable protection 
against harmful interference in a residential installation. This equipment 
generates, uses and can radiate radio frequency energy and, if not 
installed and used in accordance with the instructions, may cause 
harmful interference to radio communications. However, there is no 
guarantee that interference will not occur in a particular installation. If 
this equipment does cause harmful interference to radio or television 
reception, which can be determined by turning the equipment off and 
on, the user is encouraged to try to correct the interference by one or 
more of the following measures:

 

– Reorient or relocate the receiving antenna.

 

– Increase the separation between the equipment and receiver.

 

– Connect the equipment into an outlet on a circuit different from that 

to which the receiver is connected.

 

– Consult the dealer or an experienced radio/TV technician for help.

Safety precautions

For customers in Canada

IC statement:

CAN ICES-3 (B)/NMB-3(B) 

Notes on use

Turntable body

• Do not place and use the product in locations that are considerably 

hot or humid, dirty, or subject to extreme vibrations.

• The product should be positioned on a flat, level surface.

Cartridge

• Attach the protector to protect the stylus when the product is not in 

use.

• Do not touch the stylus of the cartridge with your finger.
• Do not allow the cartridge's stylus to bump against the platter or the 

edge of the record.

Содержание AT-LPW30TK
















Отзывы: