manualshive.com logo in svg

AuCom EMX4i, Руководство пользователя, Страница: 100 / 126

Поделиться
Скачать
AuCom EMX4i Скачать руководство пользователя страница 100

PROGRAMMABLE PARAMETERS 

710-14888-00C  EMX4i User Manual   

 

99

 

12T – 

DHCP

 

Options: 

Disable (default)   
Enable 

Description: 

Selects whether the communications card will accept an IP 
address assigned by DHCP. 

 

 

NOTE 
DHCP addressing is available with Modbus TCP and Ethernet/IP. DHCP 
addressing is not supported with Profinet. 

12U – 

Location ID

 

Range: 

0 - 65535 

Default: 

0 

Description: 

Sets the soft starter's unique location ID. 

9.17

 

20 Advanced 

20A – 

Tracking Gain

 

Range: 

1% - 200% 

Default: 

50% 

Description: 

Fine-tunes the behaviour of the adaptive control algorithm. 

20B – 

Pedestal Detect

 

Range: 

0% - 200% 

Default: 

80% 

Description: 

Adjusts the behaviour of the adaptive control algorithm for soft 
stop. 

20C – 

Bypass Contactor Delay

 

Range: 

100 – 2000 milliseconds 

Default: 

150 milliseconds 

Description: 

Sets the starter to match the bypass contactor closing/opening 
time. Set according to the specifications of the bypass contactor 
used. If this time is too short, the starter will trip. 

20D – 

Model Rating

 

Range: 

0020~0580 

Default: 

Model dependent 

Description: 

The soft starter’s internal model reference, as shown on the 
silver label on the side of the unit (

).   

M/R: 0085

Made in New Zealand

RoHS

18595.

B

1

 

 

 

NOTE 
This parameter can only be adjusted by authorised servicing agents.   

Содержание EMX4i































































































































Отзывы:

Нет отзывов