ATV NVW4212M Скачать руководство пользователя страница 15

Страница: 15 / 88

3.4 Live View Page

The Live View page comes in several screen modes. Users are allowed to select the most
suitable one out of those modes. Adjust the mode in accordance with your PC specifications and
monitoring purposes.

1) General controls

Live View Page

Playback Page

Setup Page

Help Page

The video drop-down list allows you to select a customized or pre-

programmed video stream on the Live View page. Stream profiles are con-
figured under Setup

Basic Configuration

Video & Image. For more in-

formation, please see

“Basic Configuration

Video &

Image” of User Manual.

The resolution drop-down list allows you to select the most suitable one out of

video resolutions to be displayed on Live View page.

The protocol drop-down list allows you to select which combination of protocols

and methods to use depending on your viewing requirements, and on the
properties of your network.

2) Control toolbar

The live viewer toolbar is available in the web browser page only. It displays the following
buttons:

The

Stop

button stops the video stream being played. Pressing the key again toggles the

start and stop. The

Start

button connects to the network camera or starts playing a video

stream.

The

Pause

button pauses the video stream being played.

The

Snapshot

button takes a snapshot of the current image. The location where the image is

saved can be specified.

Содержание NVW4212M

























































































Результаты поиска

Содержание NVW4212M

Отзывы:

ATV NVW4212M, Руководство пользователя, Страница: 15 / 88

Результаты поиска

Содержание NVW4212M

Отзывы: