All-Round Lights: 5940, 5980
Sidelights: 5040, 5045, 5080
Installation Instructions
SAVE THESE INSTRUCTIONS
Form Number 69379 Rev. B
03-10
3
®
12-Volt
Navigation Lights
Green
(Starboard)
Red
(Port)
Green
(Starboard)
Red
(Port)
Figure 2
Figure 1
One meter
or 39-3/8"
LOCATION (Sidelights)
Mount sidelights to a smooth surface on the gunwale, deck or
superstructure where the light beam will not be obstructed. Position Bi-
Color combination light as far forward as possible. (Figure 2)
Important: Before drilling mounting holes, be sure sidelights shine straight
ahead and that they shine within 5
°
of horizontal when the boat is floating.
FEATURES
The Attwood Pulsar Navigation Lights are designed for boats upto 39.6 ft.
(12 meters). They feature impact resistant, UV-stable polycarbonate
housings. The lens completely encloses the bulb and socket for a splash
resistant seal. Lights meet USCG CFR 183.810, ABYC A-16 requirements,
and all applicable standards as tested by Imanna Labs, March 1997.
5040, 5045, and 5080 are Sidelights with 1 Nautical Mile visibility. 5940
and 5980 are All-Round Lights with 2 Nautical Mile visibility. All use Lamp
9235, #906, 13V, 6 Candle Power.
REQUIRED FOR INSTALLATION
• Cordless drill with 1/8", 3/8", and 3/4" (3, 10, and 19mm) bits.
• Screwdriver.
• Two #8 or #10 stainless pan head screws per light.
• Non-silicone sealant.
WARNING:
To prevent personal injury, disconnect the power source when installing
or servicing this product. Always remove the boat from the water before
using 120V AC power tools.
LOCATION (All-Round Lights)
All-Round Lights must be mounted a minimum of 1 meter above the
sidelights, on a smooth surface where the 360
°
beam will not be obstructed.
Light must not shine on operator or on anything in operator’s field of view.
(Figure 1)
Important: Before drilling mounting holes, be sure that light shines within
5
°
of horizontal when the boat is floating.
INSTALLATION, DECK MOUNT
All-Round Lights
1. To access mounting holes, gently twist lens helmet counterclockwise
to remove.
2. Place light in position as shown in Figure 1.
Important: Before drilling, be sure that light will shine within 5
°
of
horizontal when boat is floating.
3. Mark and drill 3/4" (19mm) diameter hole. (Figure 3)
4. Thread wire leads and base stem into hole. Mark location of screw
holes. Proceed to Step 5 below.
Bi-Color Sidelights and Sidelight Pairs
1. To access mounting holes, gently twist lens helmet counterclockwise
to remove.
2. Place sidelight(s) in position as shown in Figure 2.
Important: Before drilling, be sure that sidelights will shine straight
ahead and within 5
°
of horizontal when boat is floating.
3. For Bi-Color Combination light, mark and drill a 3/4" (19mm) diameter
hole on the boat centerline. For Sidelight Pairs, mark and drill a 3/4"
(19mm) diameter hole on each side deck of the boat, equal distance
from the bow. (Figure 3)
4. Thread wire leads and base stem into hole. Align centerline mark with
straight-ahead position and mark location of screw holes.
5. Remove base and drill 1/8" (3mm) pilot holes for both screws.
6. Bring 12V DC (+) and (-) wires up through deck hole. Connect wires
using waterproof crimp on butt joint connectors.
7. Activate light to verify proper operation.
8. Apply a thin bead of non-silicone sealant into groove on underside
of base to prevent water from entering hull or cabin. Do not allow
sealant to enter the lens bayonet channels.
9. Align and fasten base with stainless screws. Do not over tighten.
10. Replace lens helmet flush on base and turn clockwise until click is
heard and felt. (Figure 3)
Off
Lens Helmet
"O" Ring
Lens Bayonet Channels
Centerline Mark
1/8" (3mm) Pilot Holes
3/4" (19mm) Dia. Hole
On
•
•
•
•
•
•
Figure 3
