manualshive.com logo in svg

ATS SuperTrak GEN3, Руководство по эксплуатации и обслуживанию, Страница: 329 / 366

Поделиться
Скачать
ATS SuperTrak GEN3 Скачать руководство пользователя страница 329

   Appendix C: Component Data Sheets

SuperTrak™ GEN3 System Operation and Maintenance Manual

317

Rev. 9 (12-2021)

Straight Section with RME Data Sheet

The straight section with rear mounted electronics (RME) generates and regulates 
the electromagnetic field for the pallets.

Features

•

Bevels on the upper v-rail 
overlap at SuperTrak 
conveyance platform section 
transitions to provide a 
smooth, low-vibration 
transport surface for pallets.

•

Access to the electronics 
from the front is not 
required, since the 
electronics are mounted in 
the rear.

•

Low-profile stands allow for 
a low profile installation.

•

Includes: 

• Encoders for contact-

free position tracking of 
pallets.

• Eight (8) slots for mounting brackets, cable ducts, and other tooling.

• Two (2) stands for stable mounting on a frame and smooth height 

adjustment.

• Rear mounted electronics, to allow for a horizontal or vertical 

 

(also known as over/under) installation.

•

Options include:

• Standard-height stands

• Low-profile  stands

•

Requires minimal maintenance (weekly cleaning of the flat wear strip).

Part Numbers

Part

Part Number

Straight section with rear-mounted electronics and

 

low-profile stand

125414648

Straight section with rear-mounted electronics and

 

standard-height stand

125780473

Содержание SuperTrak GEN3















































































































































































































































































































































































Отзывы:

Нет отзывов