manualshive.com logo in svg

ATS SuperTrak GEN3, Руководство по эксплуатации и обслуживанию, Страница: 162 / 366

Поделиться
Скачать
ATS SuperTrak GEN3 Скачать руководство пользователя страница 162

150

 SuperTrak™ GEN3 System Operation and Maintenance Manual 

Rev. 9 (12-2021)

Technician Procedures

Replace a Coil Driver Board

This section describes how to replace a coil driver board in a straight section or in 
a 180 deg. section.

Remove a Coil Driver Board - Straight Section 

1. Turn the 

SuperTrak conveyance platform power disconnect switch 

to 

the OFF position.

2. Lock out and tag hazardous energy.

See 

Lockout and Tagout Locations

 on page 12.

3. Use a flat head screwdriver to unlock the 

five (5) locks, and then open the electrical 
door.

4. Unplug the two (2) ribbon cables. 

Pull each of the four (4) ribbon cable plugs 
straight out.

5. Unplug the five (5) coil plugs.

Pull each coil plug straight out.

To prevent electrical board damage from electrostatic discharge (ESD), 
use an ESD wrist strap when working with the coil driver board. An ESD 
wrist strap prevents the buildup of static electricity.

Содержание SuperTrak GEN3















































































































































































































































































































































































Отзывы:

Нет отзывов