ATS SuperTrak GEN3 Скачать руководство пользователя страница 107

Страница: 107 / 366

Installation

SuperTrak™ GEN3 System Operation and Maintenance Manual

Rev. 9 (12-2021)

Level the Frame

To accommodate varying floor heights, the leveling feet of the SuperTrak
conveyance platform frame allow for individual height adjustment.

1. Place a precision spirit level across the frame in the directions illustrated, to

determine the leveling foot (or feet) that requires adjustment.

2. If installed, remove the anchor bolt and hold down toe.

3. Loosen the upper lock nut.

4. Turn the leveling foot as required, to raise or lower the table.

5. Use a level to verify that the table is level.

6. If the frame is not level, repeat steps 1 to 5.

7. Tighten the upper lock nut.

8. If required, install the hold down toe over the lower lock nut.

9. Tighten the anchor bolt.

Hold down toe

Anchor bolt and washer

Frame

Upper lock nut

Lower lock nut

Leveling foot

Содержание SuperTrak GEN3















































































































































































































































































































































































Результаты поиска

Содержание SuperTrak GEN3

Отзывы:

ATS SuperTrak GEN3, Руководство по эксплуатации и обслуживанию, Страница: 107 / 366

Результаты поиска

Содержание SuperTrak GEN3

Отзывы: