ATS Co-Pilot Скачать руководство пользователя страница 2

Страница: 2 / 12

improve reliability, whether you have a stock daily driver or a fully built race truck! Give us a

call today if you feel the need to get a fully rebuilt transmission for your truck, or if you just

want to strengthen your current transmission with a few upgraded parts. Our experts can help

answer any questions you have and guide you in the right direction.

Setting up the ATS Co-Pilot module for installation

The ATS Co-Pilot will need to be set up for your vehicle and application. The Co-Pilot will

need to be disassembled to access the dip switches on the electronic board. You will need a

1/16

- inch hex (Allen wrench) to remove the face from the Co-Pilot. After the face has been

removed the electronic board can be slid out of the casing from the front. The digital face is

attached to the circuit board with a ribbon cable; do not force the board from the case. There are

four (4) switches on the circuit board; the switches allow the user to select the features desired.

The settings are listed below. When reinstalling the face on the Co-Pilot do not over tighten the

2 small screws on the face.

Dip switch selection:

---------------------------------------------------------------------------------------------------------------------------------------

Switch #1

Set to

OFF

position

---------------------------------------------------------------------------------------------------------------------------------------

Switch #2

Set to

position

----------------------------------------------------------------------------------------------------------------------------------------

Switch #3 -

Speed setting

On=low speed cut out

Off= Hi speed cut out

----------------------------------------------------------------------------------------------------------------------------------------

Switch #4

Set switch to

position

---------------------------------------------------------------------------------------------------------------------------------------

We have preset your module with #1-OFF, #2-ON, #3-OFF, and #4-ON.

Содержание Co-Pilot













Результаты поиска

Содержание Co-Pilot

Отзывы:

Похожие инструкции для Co-Pilot

Бренды по названию

Популярные бренды

ATS Co-Pilot, Руководство по установке

Результаты поиска

Содержание Co-Pilot

Отзывы:

Похожие инструкции для Co-Pilot

Бренды по названию

Популярные бренды