ATS 2140-M Series Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 115

ATS 2140-M Series Скачать руководство пользователя страница 30

30

The WinCCS Modular requires the address to be set on the CPU Board via dip switches.

Each frame controller services two frames, and they have been designated left (main) and right

(secondary). The controller is commonly mounted on the main tester. Enter the proper designation in

the Side pull-down list under Frame Controller Information.
Except in the rare case that a frame controller is configured to support only one frame, the proper

designation under Type should be listed as Dual.

6.2.3 Frame Load Capacity

The minimum and maximum frame loads are specified by the frame manufacturer, and it is important

that the correct information be entered. The frame load specified during any test is checked against this

information, and tests which require loads outside the specified limits are not allowed to run. This can

protect the frame and load components from damage. To access frame load, click on System—Frame

Setup and enter the appropriate information under Frame Load Capacity.
NOTE: Do not change the minimum load capacity, or the test will lose accuracy.

6.2.4 Frame Naming

Each frame must be given a unique name. The default name, which is the frame number, can also be

used. To assign a specific name to a frame, go to Frame Setup. Click on the General Information box

and enter the frame title in the Name box. The name entered in this space will be viewed on the status

display screen and used in all reports and graphs.
At this point, the operator can now set up the various submenus listed under Frame Setup by clicking

through the tabs.

«
...
28
29
30
31
32
...
»

Содержание 2140-M Series




















































































































Отзывы:

Нет отзывов