ATS 2140-M Series страница 15 Скачать руководство пользователя | Manualshive

Страница: 15 / 115

background image

15

3.3 Unpacking Equipment

Carefully unpack the equipment and inspect it for damage during shipment. Retain all cartons and

packaging materials until the unit is operated and found to be in good condition. If damage has occurred

during shipping, notify the carrier and ATS immediately. If it is necessary to file a damage claim, retain

the packing materials for inspection by the carrier.
Unpacking and Setup
1. Carefully remove the shipping crate and packing materials. Do not discard the packing

materials until all items on the invoice have been accounted for.

2. Use an overhead crane or forklift to remove the test frame and control console from the pallet

and position it in the desired location.

NOTE: Use moving blankets between unit components, and follow accepted moving practices to avoid

damage to the tester.
NOTE: Position the test frame and console to allow ample room for maintenance.
3. If casters are supplied with the unit, install them in the cabinet base when it is lifted off the pallet.

4. Adjust the isolator mounts on the test frame to approximately level, ensuring even support.

CAUTION: Do not allow the isolator mount pads to slide on the floor while moving the tester.

They are not designed to accept side loading. Damage to the pads may result.

5. If applicable, connect the cables between the load frame and the control console.

6. Connect electrical power to the customer power terminal block. Proper grounding is a MUST.

NOTE: Follow all local and national codes, and be sure to use the correct voltage and amperage. Refer to

equipment data tag for the individual unit information.

CAUTION: Turn all power switches to OFF and place all controls in a neutral position before

supplying power to the machine.

«
...
13
14
15
16
17
...
»

Содержание 2140-M Series




















































































































Отзывы:

Нет отзывов

Похожие инструкции для 2140-M Series

Бренд: ZOLL Страницы: 84

Бренд: Kaivac Страницы: 29

Бренд: MacDon Страницы: 65

Бренд: B&K Страницы: 8

Бренд: Taylor Made Страницы: 2

Бренд: York Fitness Страницы: 18

Бренд: Safco Страницы: 2

Бренд: Omni Страницы: 193

Бренд: Napoleon Страницы: 2

Бренд: Raytheon Страницы: 62

Бренд: KaVo Страницы: 13

Бренд: vc999 Страницы: 52

D-IMager EKL3104

Бренд: Panasonic Страницы: 13

Бренд: Labokey Страницы: 5

Бренд: E-Z Trail Страницы: 8

Бренд: B&K Страницы: 10

Бренд: CAIRE Страницы: 2

D-MAS HyperSat 2540

Бренд: DanMedical Страницы: 103

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды