ATS 2140-M Series Скачать руководство пользователя страница 114

Страница: 114 / 115

114

Appendix D: Warranty

This appendix includes all required information for the WinCCS tester.

Warranty Statement

Your Applied Test Systems product has been manufactured and inspected by experienced craftsmen.

Applied Test Systems warrants, for the original purchaser, each product to be free from defects in

material and workmanship for a period of thirteen (13) months from date of shipment or twelve (12)

months from date of installation whichever comes first. This warranty does not apply to failures caused

by normal usage, misuse, or repair or service by unauthorized personnel, nor does it cover limited life

electrical components which deteriorate with age such as tubes, lamps, fuses, and heaters. The warranty

does not extend to products not manufactured or assembled by Applied Test Systems.

This warranty is expressly limited to the repair, replacement, or adjustment of the product at Applied

Test Systems’ option. The product must be returned to the Applied Test Systems factory or an authorized

repair center. Applied Test Systems shall not be liable for any labor, transportation, or installation costs

that may arise in connection with the product or return.

To obtain warranty service:

1. Applied Test Systems must be promptly notified in writing of the defect.

2. Upon receipt of written authorization, said defective equipment is returned as directed, with

transportation charges prepaid by the buyer and –

3. Applied Test Systems examination of such equipment discloses to its satisfaction that the

defect exists and was not caused by negligence, misuse, improper installation, accident,

or unauthorized repair or alteration.

This warranty is in lieu of all other warranties, expressed or implied, including the implied warranty of

merchantability or fitness for particular purpose. In no event shall Applied Test Systems be liable for

direct, indirect, special, incidental, collateral or consequential damages.

The aforementioned provisions do not extend the original warranty period of any article that has been

either repaired or replaced by Applied Test Systems.

Applied Test Systems reserves the right to change published specifications.

154 East Brook Lane | Butler, PA 16002 USA | +1-724-283-1212

Содержание 2140-M Series




















































































































Результаты поиска

Содержание 2140-M Series

Отзывы:

ATS 2140-M Series, Инструкция по эксплуатации, Страница: 114 / 115

Результаты поиска

Содержание 2140-M Series

Отзывы: