ATS 2140-M Series страница 107 Скачать руководство пользователя

Страница: 107 / 115

107

B2: States that occur while Running a Test

All Specimen Thermocouples are Open:

All control thermocouples are open and the test will be shut

down.

Automatic Loading Failed:

The automatic creep loading system failed; this statement is usually

accompanied with a reason for load failure.

Automatic Loading Timed Out:

The automatic creep step loading routine failed due to insufficient load

change during the loading procedure.

Cannot Start, Open TCs:

One or more thermocouples are open during the initial start-up or ramp of the

specimen.

Check Furnace Alarm, Shutdown:

A fatal temperature event precedes this message. This indicates the

actual shutdown of the furnace control due to that event.

Control T/C Switched to Highest T/C:

Informational alarm which indicates that the temperature control is

completely stable and the control is now on the highest physical thermocouple in the furnace.

Furnace Split Exceeded:

Indicates the system has adjusted the power split between the zones as much as

possible and was not able to control temperature uniformity.

ISO Thermal Temperature Range Error, Shutdown:

The temperature measurement subsystem ambient

temperature sensor is outside the range of normal operation, which is less than 32 degrees Fahrenheit

or greater than 120 degrees Fahrenheit.

Rezero of Extensometer Requested:

The system has detected that the specimen has creeped close to the

range of the displacement transducer. The system is requesting a mechanical rezero of the extensometer.

Shutdown Due to Furnace Out of Band Time Exceeded:

The furnace has been out of band limits for

more than fifteen minutes and the ramp up will be terminated. Check for the following conditions:
1. Open furnace element or solid state relay

2. Specified ramp rate is too fast

3. Shorted thermocouple

4. Low AC line voltage

Specimen Broke During Loading:

The system was loading the specimen and after five minutes the break

switch never went to a not broken state. The system assumes that the specimen broke.

Specimen is Ready to Load Weights:

The specimen is ready to be loaded on manual frames.

Specimen Loaded:

The specimen was loaded by the system.

Содержание 2140-M Series




















































































































Результаты поиска

Содержание 2140-M Series

Отзывы:

Похожие инструкции для 2140-M Series

Бренды по названию

Популярные бренды

ATS 2140-M Series, Инструкция по эксплуатации

Результаты поиска

Содержание 2140-M Series

Отзывы:

Похожие инструкции для 2140-M Series

Бренды по названию

Популярные бренды