ATS 2140-M Series страница 106 Скачать руководство пользователя

Страница: 106 / 115

106

Appendix B: Glossary

B.1 Prompts that may appear during Setup and Running a Test

Apply Load:

The load is applied to the specimen.

Cal/Ver:

The frame is having the extensometer calibrated, verified, or checked.

Disable:

This state makes sure that if the termination was due to a temperature alarm that the specimen

did not actually break.

Fault:

A hardware fault has occurred on the frame.

Idle:

The frame status is idle.

Initial Load:

Sets the initial drawhead or elevator position before ramping the furnace.

Loading 2:

No action, except to take the frame offline. Used by the test load control.

Load Invalid:

The load control has been unable to maintain the load within the 1% limit for over five

minutes.

Manual:

The frame is in manual control.

Pre Start up:

The frame is requested to start; all parameters are downloaded to the frame controller.

Post Test:

The test is complete and ready to be removed.

Ramp:

The furnace is ramped from the current temperature up to the setpoint. When at least one of the

thermocouples is within the minor limit, the soak state is entered.

Remove:

The frame controller is waiting for the host to upload the final test data before the specimen is

removed.

Restart:

The system is restarting the test after a power failure.

Run:

Normal running state of the test.

Shutdown:

Entered at the termination of a test. Stops all frame motion and stops the furnace.

Soak:

Furnace soak state.

Start-up:

Refers to frame status.

Start-up Delay:

Test start-up was delayed.

Terminate:

This state is entered when a test is terminated by the operator.

Unload:

The load on the specimen is removed.

WF Power:

A power failure has just occurred and the system is waiting for the hardware to reinitialize.

Содержание 2140-M Series




















































































































Результаты поиска

Содержание 2140-M Series

Отзывы:

Похожие инструкции для 2140-M Series

Бренды по названию

Популярные бренды

ATS 2140-M Series, Инструкция по эксплуатации

Результаты поиска

Содержание 2140-M Series

Отзывы:

Похожие инструкции для 2140-M Series

Бренды по названию

Популярные бренды