ATS 2140-M Series страница 102 Скачать руководство пользователя

Страница: 102 / 115

102

Appendix A: System Status Display

A.1 Status Display Headings

Frame:

Each frame has an identifier, either a name assigned during the setup process, or a number from

one to the total system complement. The default lists frames in numerical order.

State:

The frame state allows the operator to monitor the process of the test.

Specimen Name:

The specimen name is the unique identifier assigned to the particular test subject

installed in the frame. This identifier will be used for all archival purposes for subsequent test data.

Setpoint:

The setpoint is the temperature specified in the test specification to which the specimen will

be tested. In case of room temperature tests and idle frames, N/A is displayed to indicate the furnace is

not in use.

Average:

This column displays the average of the temperatures of all the thermocouples in use on this

frame. The user thermocouple is not included in this average.

Top (Middle, Bottom):

The display here assumes that three thermocouples are in use, and the

temperature of the uppermost thermocouples is displayed here. The middle and lower thermocouples

are likewise shown in the adjacent columns.

Power:

At any time during the test, the furnace control algorithm will be varying the power into the

furnace in order to keep the temperature at the specified value. This display, which is a % of the total

power available, provides an indication to the operator of the power level being delivered to the furnace.

Time:

Depending on the frame state, time may have different meaning. For example, if a test is running

normally, time will be the total run time of the test, starting from initial specimen loading. A frame in

soak state will show the time remaining until specimen loading.

% Creep:

When a creep test is in process, this display will show the amount of creep of the specimen in

real time.

Alarms:

This display shows an abbreviation name for the alarm state of the frame. In addition, this

column indicates to the operator that some action at the individual frame is required. For example, load

weights, zero extensometer, etc. may appear in this column.

Содержание 2140-M Series




















































































































Результаты поиска

Содержание 2140-M Series

Отзывы:

Похожие инструкции для 2140-M Series

Бренды по названию

Популярные бренды

ATS 2140-M Series, Инструкция по эксплуатации

Результаты поиска

Содержание 2140-M Series

Отзывы:

Похожие инструкции для 2140-M Series

Бренды по названию

Популярные бренды