Atracsys fusionTrack 500 Скачать руководство пользователя страница 51

Страница: 51 / 114

User manual

Version: v4.5.2

8.1.3 Detection stage related options

This section presents the options which are related to the 3D reconstruction of points and markers.

Name

Type

Description

Blob Minimum Aspect
Ratio

float32

read / write

Defines the the minimal aspect ratio to consider
a

raw data

during the raw detection phase. For

example, an aspect ratio of 1 means that the
bounding box of the

raw data

is a square. An

aspect ratio of 0

5 defines a rectangle with one

edge of length

and the other of length

Blob Minimum Surface

int32

read / write

Defines the minimal surface in pixels to consider
a

raw data

during the raw detection phase. This

threshold allows to reject small polluting regions
in the picture.

Blob Maximum Surface

int32

read / write

Defines the maximal surface in pixels to consider
a

raw data

during the raw detection phase. This

threshold allows to reject large polluting regions
in the picture

Symmetrise coordinates

int32

read / write

Allows to toggle on/off the symmetrised coordi-
nate system. When on, the origin of the coordi-
nate system is computed as the point between
the left and the right cameras.

Epipolar Maximum Dis-
tance

float32

read / write

Defindes the maximum distance (in pixels) be-
tween the right

raw data

and the right epipolar

line defined by the left candidate during the match
search.

Matching Tolerance

float32

read / write

Defines the tolerance in mm between the mea-
sured and reference lengths defined by two

fidu-

cials

of a

marker

, during the

marker

matching

phase. The behaviour of this option is not cor-
responding to its expected behaviour, i.e a value
of 5 mm does actually

not

correspond to a toler-

ance of 5 mm on the matched distance. If this op-
tion is changed when the new algorithm is used,
a warning is issued.

Registration Mean Error

float32

read / write

Defines the tolerance in mm after registration of
the

marker

geometry with the measured one.

Matching

Maximum

Missing Points

int32

read / write

Defines the maximum numbers of missing points
when reconstructing a

marker

candidate valid

during the

marker

matching phase (see the

‘Matching Maximum Missing Points’ paragraph
of Section 7.8 for more details).

Tracking range

float32

read / write

Defines the range (in pixels) where to look for a

raw data

associated to a

marker

according to its

position in the previous frame(s) (See ‘Tracking
time span’).

Atracsys / 2020-06-17 / 16:48:00

50 / 113

Содержание fusionTrack 500



















































































































Результаты поиска

Содержание fusionTrack 500

Отзывы:

Похожие инструкции для fusionTrack 500

Бренды по названию

Популярные бренды

Atracsys fusionTrack 500, Руководство пользователя

Результаты поиска

Содержание fusionTrack 500

Отзывы:

Похожие инструкции для fusionTrack 500

Бренды по названию

Популярные бренды