
Industrial IEC61850-3 Managed Gigabit
Ethernet Switch
EHG9508 / EHG9512 Series
Version 0.1
Updated in March, 2016
P/N:89900493G
Inside the package you will find the following items:
■ Industrial Managed Gigabit Ethernet Switch x 1
■ 4-Pin 5.08mm Lockable Terminal Block (Already mounted to the device) x 1
■ 5-Pin 5.08mm Lockable Terminal Block (Already mounted to the device) x 1
■ DIN-Rail Kit (Already mounted to the device) x 1
■ Protective caps for all SFP ports (Depend on purchased model)
■ Installation Guide with Warranty Card x 1
Front View
1. Ring LED
2. RUN LED
3. Ring Master LED
4. Alarm LED
5. SFP Ports LEDs
6. PWR1 LED
7. PWR2 LED
8. 1000 BASE-X SFP Slots
9. 10/100/1000 BASE-T(X) RJ-45 Ports
10. DI Status
Never install or work on electrical or cabling during periods of lightning activity.
Never connect or disconnect power when hazardous gases are present.
Warning:Hot Surface Do Not Touch.
Caution: CLASS 1 LASER PRODUCT. Do not stare into the laser!
Indoor
Indoor
This equipment should be installed indoor and not connect directly with equipment
installed outdoor.
EHG9508-2SFP
EHG9508-2SFP-HV
EHG9512-4SFP
EHG9512-4SFP-HV
Ring
1 2 3 4
5
10
8
9
R.M. RUN ALM
P1
DI
P2
SFP
1
1
3
4
5
8
7
6
2
2
Ring R.M. RUN ALM
P1
DI
SFP
1
1
3
4
5
8
7
6
2
2
Ring R.M. RUN ALM
P1
P2
DI
SFP
1
2
6
7
8
12
11
10
5
9
4
1
3
2
3
4
Ring R.M. RUN ALM
P1
DI
SFP
1
2
6
7
8
12
11
10
5
9
4
1
3
2
3
4
6 7
1 2 3 4
6
10
6 7
10
10
5
8
9
1 2 3 4
6
1 2 3 4
5
8
9
8
5
9
1. Grounding Screw
2. DIP Switches
3. RS-232 Console
4. Reset button
5. Relay Output 1 with current carrying
6. Digital Input
7. Frame Ground
8. Terminal for Power 1
9. Terminal for Power 2
1
1
2
2
You can then choose whether to plug in the other
peripheral ports at this point or do it later depending
on the actual location of the device or level of
comfort for performing such operation.
Remeber to plug in the protective caps for the
unused SFP.
3.
Once the plate has been firmly put in place, proceed
to mount the whole device as shown in (Fig.
3).Proceed to (Fig. 4) if you want to remove the
device from DIN-Rail.
4.
Next we can then proceed to connect the device to
the LAN (switch or PC, depending on the case), take
care on using the RJ-45 connector; after this we can
then proceed to the device’s settings
5.
If you have purchased the wall mount kit,
proceed to place the screws on the back
of the device as show in (Fig. 1).
1.
2. Although internal grounding has been
done inside, in order to ensure overall
maximum performance and protect your
device, it is still strongly advised to ground
the device properly; hazardous ESD can
come into contact and damage your
equipment. On the power terminal block,
there is a terminal for Frame Ground, you
can choose whether to connect it to the
grounding or you may opt to connect to
the grounding screw next to the terminal
block ( the one chosen should be connect-
ed at all times ) (Fig. 2)
Relay
DI
+
Reset
C
onsole
V1+
V2–
V2+
V1–
!
Relay
DI
+
Reset
C
onsole
V1+
V2–
V2+
V1–
!
6
7
8
9
5
1
2
3
4
Color
Status
Name
Message
P1
P2
ALM
RUN
Ring
R.M.
SFP
DI
LAN
Green
Red
Green
Green
Green
Green
Green
Amber
Green
On
Off
On
Off
Blinking
On/Off
On
Blinking
Off
On
Off
On
Blinking
Off
On
Off
On
Blinking
Off
On
Blinking
Off
Power is being supplied through this power input
Power is not supplied through this power input
Alarm is triggered by user defined events
Alarm is not triggered by user defined events
AP firmware is running normally
System is not ready or halt
All the Rings are running normally
Ring is in protection state
Ring is disabled
The device is a Master of the Ring
The device is a Slave of the Ring
Port is linked
Data is transmitting on this port
No data is transmitting on this port
Status is on
Status is off
Ethernet is connected at 1000Mbps
Ethernet is connected at 100Mbps
Ethernet is connected at 10Mbps
Ethernet is connected
Data is transmitting on this port
Ethernet is disconnected
■ The opening to the sides are for the device’s
heat dissipation please never obstruct or
cover them with any objects or try to insert
them through it.
■ This switch’s factory IP by default is 10.0.50.1
you can access the device by its Web UI
once it is connected to a physical network (or
using Management Utility, for more informa-
tion on Management Utility, please refer to its
manual). Please be aware that the PC
needed for this procedure needs to be in the
same subnet, or you may refer yourself to
the device User’s Manual.
Relay
DI
+
Reset
C
onsole
V1+
V2–
V2+
V1–
!