background image

EN

www.atmos.cz

20-EN

Operation and Maintenance Manual - EN

WARRANTY PROVISIONS

A85 pneumatic burner cleaner

1.  If you observe the method of use, operation and maintenance of this product described in this 

manual, we guarantee that the product will keep the properties described by relevant technical 

standards and conditions over the whole warranty period, this being within 24 months from the 

day of receipt of the appliance, and a max. 32 months from the date of sale of the product by the 

sales representative.

2.   If a fault occurs with the product during the warranty period which was not caused by the user, 

the product will be repaired under the warranty free of charge for the customer.

3.   The warranty period is extended by the time over which the product is repaired under warranty.

4.   Repairs undertaken during the warranty period are claimed by the customer using our service 

operations.

5.   The product warranty is only recognised where the equipment is assembled by a qualified person 

in accordance with standards in force and the operation manual. A requirement for any warranty 

to be recognised is the details on the company which performed the assembly being legibly and 

fully completed. If the product is damaged through poor assembly, costs associated will be borne 

by the company which performed the assembly.

6.   The purchaser has been demonstrably informed of the use and operation of the product.

7.   Repairs undertaken after the warranty period ends are also claimed by the customer using our 

service operations. In this case, the customer pays the cost of repair himself.

8.   The user is required to observe the instructions in the Operation and Maintenance Manual. If the 

customer does not follow the Operation and Maintenance Manual instructions, is careless, or 

handles the product incorrectly, the warranty is void and the customer is required to pay for any 

repairs resulting from damage

Warranty and post-warranty repairs are performed by:

- the company representing ATMOS in your country for your region

- the assembly company which installed the product

Jaroslav Cankař a syn ATMOS,

  Velenského 487

294 21 Bělá pod Bezdězem, Česká republika, Tel. +420 326 701 404

Содержание CP85KS





















Отзывы: