Atmel AVR XMEGA D Series Скачать руководство пользователя страница 267 | Manualshive

Страница: 267 / 331

Atmel AVR XMEGA D Series Скачать руководство пользователя страница 267

267

8210C–AVR–09/11

Atmel AVR XMEGA D

21.15.3

INTCTRL – Interrupt Control registers

• Bits 7:4 – Reserved

These bits are unused and reserved for future use. For compatibility with future devices, always
write these bits to zero when this register is written.

• Bit 3:2 – INTMODE: Interrupt Mode

These bits select the interrupt mode for the channel according to

.

• Bits 1:0 – INTLVL[1:0]: Interrupt Priority Level and Enable

These bits enable the ADC channel interrupt and select the interrupt level, as described in

rupts and Programmable Multilevel Interrupt Controller” on page 101

. The enabled interrupt will

be triggered for conditions when the IF bit in the INTFLAGS register is set.

21.15.4

INTFLAGS – Interrupt Flag registers

• Bit 7:1 – Reserved

These bits are unused and reserved for future use. For compatibility with future devices, always
write these bits to zero when this register is written.

• Bit 0 – IF: Interrupt Flag

The interrupt flag is set when the ADC conversion is complete. If the channel is configured for
compare mode, the flag will be set if the compare condition is met. IF is automatically cleared

101

-

Reserved

110

-

Reserved

111

GND

PAD ground

Table 21-13.

ADC MUXNEG configuration, INPUTMODE[1:0] = 11, differential with gain

Bit

7

6

5

4

3

2

1

0

–

–

–

–

INTMODE[1:0}

INTLVL[1:0]

INTCTRL

Read/Write

R

R

R

R

R/W

R/W

R/W

R/W

Initial Value

0

0

0

0

0

0

0

0

Table 21-14.

ADC interrupt mode.

INTMODE[1:0]

Group Configuration

Interrupt Mode

00

COMPLETE

Conversion complete

01

BELOW

Compare result below threshold

10

Reserved

11

ABOVE

Compare result above threshold

Bit

7

6

5

4

3

2

1

0

–

–

–

–

–

–

–

IF

INTFLAGS

Read/Write

R

R

R

R

R

R

R

R/W

Initial Value

0

0

0

0

0

0

0

0

«
...
265
266
267
268
269
...
»

Содержание AVR XMEGA D Series












































































































































































































































































































































Отзывы:

Нет отзывов