Atmel AVR XMEGA AU series Скачать руководство пользователя страница 248 | Manualshive

Страница: 248 / 512

background image

248

8331B–AVR–03/12

Atmel AVR XMEGA AU

20.13 Register Description – USB

20.13.1

CTRLA – Control register A

• Bit 7 – ENABLE: USB Enable

Setting this bit enables the USB interface. Clearing this bit disables the USB interface and imme-
diately aborts any ongoing transactions.

• Bit 6 – SPEED: Speed Select

This bit selects between low and full speed operation. By default, this bit is zero, and low speed
operation is selected. Setting this bit enables full speed operation.

• Bit 5 – FIFOEN: USB FIFO Enable

Setting this bit enables the USB transaction complete FIFO, and the FIFO stores the endpoint
configuration table address of each endpoint that generates a transaction complete interrupt.
Clearing this bit disables the FIFO and frees the allocated SRAM memory.

• Bit 4 – STFRNUM: Store Frame Number Enable

Setting this bit enables storing of the last SOF token frame number in the frame number (FRA-
MENUM) register. Clearing this bit disables the function.

• Bit 3:0 – MAXEP[3:0]: Maximum Endpoint Address

These bits select the number of endpoint addresses used by the USB module. Incoming packets
with a higher endpoint number than this address will be discarded. Packets with endpoint
addresses lower than or equal to this address will cause the USB module to look up the
addressed endpoint in the endpoint configuration table.

20.13.2

CTRLB – Control register B

• Bit 7:5 – Reserved

These bits are unused and reserved for future use. For compatibility with future devices, always
write these bits to zero when this register is written.

Bit

7

6

5

4

3

2

1

0

ENABLE

SPEED

FIFOEN

STFRNUM

MAXEP[3:0]

CTRLA

Read/Write

R/W

R/W

R/W

R/W

R/W

R/W

R/W

R/W

Initial Value

0

0

0

0

0

0

0

0

Bit

7

6

5

4

3

2

1

0

–

–

–

PULLRST

–

RWAKEUP

GNACK

ATTACH

CTRLB

Read/Write

R

R

R

R/W

R

R/W

R/W

R/W

Initial Value

0

0

0

0

0

0

0

0

«
...
246
247
248
249
250
...
»

Содержание AVR XMEGA AU series

































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для AVR XMEGA AU series

Бренд: D-Link Страницы: 40

Бренд: Echelon Страницы: 40

Бренд: Camozzi Страницы: 33

Бренд: Camozzi Страницы: 64

Бренд: YOKOGAWA Страницы: 2

ALICAT SCIENTIFIC PC

Бренд: Halma Страницы: 2

ALICAT SCIENTIFIC PCD

Бренд: Halma Страницы: 46

Бренд: Gateway Страницы: 2

Бренд: Oriental motor Страницы: 4

Бренд: Kelly Страницы: 35

Бренд: Velp Scientifica Страницы: 24

Бренд: Pixsys Страницы: 24

Бренд: Aaeon Страницы: 54

Бренд: Elan Страницы: 2

Бренд: Oki Страницы: 466

Бренд: Danfoss Страницы: 2

Бренд: StudioComm Страницы: 55

Бренд: YASKAWA Страницы: 23

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды