Atmel AVR XMEGA AU series Скачать руководство пользователя страница 125 | Manualshive

Страница: 125 / 512

background image

125

8331B–AVR–03/12

Atmel AVR XMEGA AU

10.6

Register Description

10.6.1

CTRL: Control register

• Bit 7: 6 – Reserved

These bits are unused and reserved for future use. For compatibility with future devices, always
write this bit to zero when this register is written.

• Bit 5 – HIGHESR: High ESR Mode

Setting this bit will increase the current used to drive the crystal and increase the swing on the
TOSC2 pin. This allows use of crystals with higher load and higher ESR.

• Bit 4 – XOSCSEL: Crystal Oscillator Output Selection

This bit selects the prescaled clock output from the 32.768kHz crystal oscillator. After reset, this
bit is zero, and the 1Hz clock output is used as input for the RTC. Setting this bit will select the
1.024kHz clock output as input for the RTC32. This bit cannot be changed when XOSCEN is
set.

• Bit 3 – XOSCEN: Crystal Oscillator Enable

Setting this bit will enable the 32.768kHz crystal oscillator. Writing the bit to zero will have no
effect, and the oscillator will remain enabled until a battery backup reset is issued. The Crystal
oscillator can also be used as 32.768 kHz system clock after performing step one to three
described in

”Configuration” on page 123

.

• Bit 2 – XOSCFDEN: Crystal Oscillator Failure Detection Enable

Setting this bit will enable the crystal oscillator monitor. The monitor will detect if the crystal is
stopped or loses connection temporarily. At least 64 swings must be lost before the failure
detection is triggered. Writing the bit to zero will have no effect, and the crystal oscillator monitor
will remain enabled until a battery backup reset is issued.

• Bit 1 – ACCEN: Module Access Enable

Setting this bit will enable access to the battery backup registers. After main reset, this bit must
be set in order to access (read from and write to) the battery backup registers, except for the
BBPODF, the BBBODF, and the BBPWR flags, which are always accessible. Writing this bit to
zero will have no effect; only a device reset will clear this bit.

• Bit 0 – RESET: Reset

Setting this bit will force a reset of the battery backup system lasting one peripheral clock cycle.
Writing the bit to zero will have no effect. Writing a one to XOSCEN or XOSCFDEN at the same
time will block writing to this bit. When this bit is set, HIGHESR, XOSCSEL, XOSCEN, and
XOSCFDEN in CTRL and XOSCRDY in STATUS will be cleared.

Bit

7

6

5

4

3

2

1

0

–

–

HIGHESR

XOSCSEL

XOSCEN

XOSCFDEN

ACCEN

RESET

CTRL

Read/Write

R

R

R/W

R/W

R/W

R/W

R/W

R/W

initial Value

0

0

0

0

0

0

0

0

«
...
123
124
125
126
127
...
»

Содержание AVR XMEGA AU series

































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для AVR XMEGA AU series

Бренд: Baccara Страницы: 16

Бренд: Hanbay Страницы: 18

Бренд: Danfoss Страницы: 16

ServeRAID-MR10is

Бренд: IBM Страницы: 94

ServeRAID-4 Ultra160 Series

Бренд: IBM Страницы: 20

Бренд: IBM Страницы: 86

Бренд: IBM Страницы: 205

Бренд: IBM Страницы: 28

Бренд: Samson Страницы: 2

Бренд: Maestra Страницы: 22

Бренд: FASAR ELETTRONICA Страницы: 2

Бренд: Seitron Страницы: 2

Бренд: Samson Страницы: 32

GL8-GL8000M3-RCA-3.0

Бренд: Balboa Instruments Страницы: 9

Бренд: Arbor Technology Страницы: 79

Бренд: H3C Страницы: 3

IC 912 Pt100-TC

Бренд: Eliwell Страницы: 4

Бренд: Regin Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды