Atmel ATSAML22G16A-AUT Скачать руководство пользователя страница 189 | Manualshive

Страница: 189 / 1231

background image

20.5. Product Dependencies

In order to use this peripheral, other parts of the system must be configured correctly, as described below.

20.5.1. I/O Lines

Not applicable.

20.5.2. Clocks

The PM bus clock (CLK_PM_APB) can be enabled and disabled in the Main Clock module. If this clock is
disabled, it can only be re-enabled by a system reset.

20.5.3. DMA

Not applicable.

20.5.4. Interrupts

The interrupt request line is connected to the interrupt controller. Using the PM interrupt requires the
interrupt controller to be configured first.

Related Links

Nested Vector Interrupt Controller

Interrupt Line Mapping

on page 44

20.5.5. Events

Not applicable.

20.5.6. Debug Operation

When the CPU is halted in debug mode, the PM continues normal operation. If standby sleep mode is
requested by the system while in debug mode, the power domains are not turned off. As a consequence,
power measurements while in debug mode are not relevant.

If Backup sleep mode is requested by the system while in debug mode, the core domains are kept on,
and the debug modules are kept running to allow the debugger to access internal registers. When exiting
the backup mode upon a reset condition, the core domains are reset except the debug logic, allowing
users to keep using their current debug session.

Hot plugging in standby mode is supported.

Cold or Hot plugging in OFF or Backup mode is not supported.

20.5.7. Register Access Protection

Registers with write-access can be write-protected optionally by the peripheral access controller (PAC).

PAC Write-Protection is not available for the following registers:

•

Interrupt Flag register (INTFLAG). Refer to

for details

Optional PAC Write-Protection is denoted by the "PAC Write-Protection" property in each individual
register description.

Write-protection does not apply to accesses through an external debugger.

Related Links

PAC - Peripheral Access Controller

on page 50

20.5.8. Analog Connections

Not applicable.

Atmel SAM L22G / L22J / L22N [DATASHEET]

Atmel-42402E-SAM L22G / L22J / L22N_Datasheet_Complete-07/2016

189

«
...
187
188
189
190
191
...
»

Содержание ATSAML22G16A-AUT
















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ATSAML22G16A-AUT

Бренд: HANYOUNG NUX Страницы: 36

Бренд: HANYOUNG NUX Страницы: 4

Бренд: MADRIX Страницы: 91

Бренд: MADRIX Страницы: 40

Бренд: YASKAWA Страницы: 18

xPico 200 Series

Бренд: Lantronix Страницы: 7

Бренд: Lantronix Страницы: 3

Бренд: Lantronix Страницы: 15

Бренд: Reer Страницы: 2

Бренд: rotork Страницы: 22

GLOFA G7M-DR20U

Бренд: LS Industrial Systems Страницы: 367

Бренд: YASKAWA Страницы: 282

Бренд: J+J Страницы: 91

Бренд: FASAR ELETTRONICA Страницы: 2

Бренд: Licht-Technik Страницы: 13

Mini-PLC STG-115

Бренд: Barth Страницы: 8

Бренд: Pilz Страницы: 23

Бренд: V2 Страницы: 108

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды