Atmel AT73C246-EK1 Скачать руководство пользователя страница 14

Страница: 14 / 48

2-4

AT73C246-EK1 Evaluation Kit User Guide

11047A–PMAAC–08-Apr-10

2.6

Power Supply

The AT73C246-EK1 is supplied by an external power supply connected on P1 (positive supply) and P2
(ground).

Figure 2-2.

Power Supply Diagram

Note:

This power supply input is NOT protected against polarization inversion.

Figure 2-3.

Vin Supply Pad (P1 & P2)

Connect the power supply (+) to P1 and the ground (-) to P2.

Note:

Keep G1 soldered to insure connection between the AGND (analog ground on P2) and
DGND (digital ground).

Table 2-1.

Electrical Supply Requirements

Power supply source

Min

Max

Unit

On P1 pad

(minimum 1 A for fully operation)

3.1

5.5

LDO 6

LDO 5

LDO 4

LDO 3

LDO 2

BUCK 0

BUCK 1

AT73C246

POWER MANAGMENT

VDD1

VDD2

VDD3

VDD4

VBACKUP

VDDC

VDD0

VIN

WAKEUP0

HRST

PWREN

AT73C246-EK1

VBACKUP

AGND

VDD0

Min 1A for

fully operation

Содержание AT73C246-EK1

















































Результаты поиска

Содержание AT73C246-EK1

Отзывы:

Похожие инструкции для AT73C246-EK1

Бренды по названию

Популярные бренды

Atmel AT73C246-EK1, Руководство пользователя

Результаты поиска

Содержание AT73C246-EK1

Отзывы:

Похожие инструкции для AT73C246-EK1

Бренды по названию

Популярные бренды