background image

      

PennEngineering • www.pemnet.com      

43

Instruction Manual - RIV938

MAINTENANCE

Maintenance operations must be carried out with the tool stopped and disconnected from the pneumatic supply line.

Warnings:

•  The tool maintenance instructions must be followed carefully.

•  To ensure safety and perfect tool efficiency, it is recommended to use exclusively ORIGINAL spare parts.

CLEANING

It is a good rule to completely clean and grease the tool on a periodic basis (depending on the type and frequency of 

use). These operations must be carried out at least once a year.

Shut-off all sources of power to the tool.
The operator must wear and use suitable personal protections before starting to clean the tool.

ORDINARY MAINTENANCE

In order to prevent stoppages and faults of the tool, an ordinary maintenance (including inspections, checks and 

operations) must be scheduled to keep the following under systematic control:

•  State of lubrication of the tool.
•  State of wear of consumable parts.

REFILLING THE HYDRAULIC CIRCUIT WITH OIL

The hydraulic circuit needs to be refilled with oil after a continuous use, and when you notice a reduction in the tool 

stroke.

Proceed as follows (see photo at right):

•  Disconnect the airline from the tool inlet.

•  Remove cap together with relevant washer 27.

•  Put the tool in horizontal position and slowly pour in the hydraulic oil 

(ISO VG 32 type) 50 until the circuit is full.

•  Screw cap back on, together with relevant washer 27.

•  Connect the tool to compressed air line and start up a couple of idle 

cycles. Stop pulling the trigger and slowly loosen screw 27; make sure 

that the circuit is full with oil and that no air bubbles are left inside.

Wear gloves when managing the oil.

Do not throw the old oil outdoors. Hand it over to an authorized waste 
disposal center.
Warning!: 
If you should accidentally spill oil on your skin, wash and rinse 

thoroughly with soap and water.

PARTS SUBJECT TO WEAR

On a periodic basis check the rubber base for wear, as this is what ensures the stability of the tool. If it should need 

replacing, order the spare base from PennEngineering indicating the year/serial number of the tool.

On a periodic basis check the screws and heads  for wear and, if necessary, replace them as indicated.

Содержание 4143400-MT

















































Отзывы: