Atlas Copco XAS 185 CD7 T4 Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 40

Atlas Copco XAS 185 CD7 T4 Скачать руководство пользователя страница 27

- 27 -

1.

More frequently when operating in a dusty

environment.

2.

Replace the element when the pressure drop exceeds
11.5 psi.

3.

Refer to the Caterpillar instruction manual

CHECK SHUTDOWN SWITCHES

With the unit running, individually unplug the following
switches to insure the unit will shutdown correctly:

1. Engine coolant temperature switch (S2)

2. Element temperature switch (S5)

3. Engine oil pressure switch (S3)

4. Low fuel switch (S6)

Lubrication oils

It is strongly recommended to use Atlas Copco branded
lubrication oils for compressor.

Compressor oil

Engine oil filter (3)

Replace

Replace

Replace

Replace

Fuel filter (Primary and Final) (3)

Replace

Replace

Replace

Engine intake and exhaust valves (3)

Adjust

Adjust

Inspection by Atlas Copco Service technician

*

MAINTENANCE SCHEDULE

Daily

Initially
Around 50 Hours

Normal
Or every 250 hours

1310 3004 30

Bi-yearly
Or every 500 hours

1310 3004 31

Yearly
or every 1000 hours

1310 3004 32

Note

* Keep the bolts of the housing, the lifting
eye, the towbar and the axle securely
tightened. Refer to Compressor/Engine
Specifications for the torque values.

!

PAROIL - M

Order number

1 gallon pail:

1615 5947 00

5 gallon pail:

1615 5947 00

55 gallon drum:

1615 5949 00

PAROIL - S

Order number

1 gallon pail:

16115 5950 00

1 gallon pail:

16115 5951 00

55 gallon drum:

16115 5952 00

(1) Additional equipment is needed to run the compressor below 18°F. Please contact Atlas Copco for more
information about Cold Weather Packages

Temperature Range

Type of Oil

Compressor

Engine

Between -13°F and 122°F

(1)

PAROIL

S

See Engine Operation Manual

Between 18°F and 104°F

PAROIL

M

15W-40

Operation of compressor in ambient temperatures lower than 18°F (-8°C) without the correct
type of oil will void your warranty and may result in element failure and/or fire.

!

«
...
25
26
27
28
29
...
»

Содержание XAS 185 CD7 T4









































Отзывы:

Нет отзывов