Atlas Copco XA146 Dd, Инструкция по эксплуатации

Страница: 16 / 32

:#&
&
:#5&
&
:#*5&
&
16
*
'+)*6 #&,756/'06 9+6* #&,756#$.'
619$#4
)RUVSHFLILFLQVWUXFWLRQVHHEHORZ
Fig. 3.7
Fig. 3.8
– Remove spring pin (1).
– Release locking nut (2) with support tools (Extension tube 3).
– Adjust required height of the drawbar.
– Tighten locking nut (2) by hand first.
– Secondly tighten locking nut (2) with a tightening torque
corresponding to table (Fig. 3.8). With an extension tube (3) (”A“
corresponding table) and handforce (”B“ corresponding table)
easy tightening is possible.
– Fix locking nut (2) with spring pin (1).
– Height adjustment should be undertaken on levelled ground and
in coupled condition.
– When readjusting, make sure that the front point of the drawbar
is horizontal to the coupling point.
– Before starting a trip, make sure that the adjustment shaft is
secure, so that the stability and safety is guaranteed while
driving. If necessary tighten the locking nut (2) corresponding to
table (Fig. 3.8).
.
+(6+0) +05647%6+105
Fig. 3.9 Lifting eye
When lifting the compressor, the hoist has to be placed in such a way
that the compressor, which must be placed level, will be lifted
vertically. Keep lifting acceleration and retardation within safe limits.
Preferably use the lifting eye (1) after opening the small door (2).
$
'(14' 56#46+0)
1. Before initial start-up, prepare battery for operation if not already
done. See section 1.7 .
2. With the compressor standing level, check the level of the engine
oil. Add oil, if necessary, to the upper mark on dipstick. Consult
the Engine Operation Manual for the type and viscosity grade of
the engine oil.
3. Check the level of the compressor oil. The pointer of oil level
gauge ( Fig. 2.3 , OLG) should register in the green range. Add oil
if necessary. See section 1.3 for the oil to be used.
4. Check that the fuel tank contains sufficient fuel. Top up, if
necessary. Consult the Engine Operation Manual for the type of
fuel.
5. Drain any water and sediment from the fuel filter until clean fuel
flows from the drain cock.
6. Press vacuator valves ( Fig. 2.3 , VV) of the air filters to remove
dust.
7. Check the air filter service indicators ( Fig. 2.3 , VI). If the yellow
piston reaches the red marked service range, replace the filter
element. Reset the indicator by pushing the reset button.
8. Check water level in engine water top tank. Top up, if necessary.
Consult the Engine Operation Manual for water/coolant
specifications.
%HIRUHWRZLQJWKHFRPSUHVVRUPDNHVXUHWKDWWKH
MRLQWVRIWKHWRZEDUDUHVHFXUHGZLWKPD[LPXP
VWUHQJWKZLWKRXWGDPDJLQJWKHWRZEDU%HVXUHWKDW
WKHUHLVQRFOHDUDQFHEHWZHHQWKHWHHWKRIWKHMRLQWV
Table
X X X M
A
[Nm] ”A“ [mm] ”B“ [N]
ZV 2000 250 - 300 600 420 - 500
ZV 2500 350 - 400 600 580 - 660
$WWHQWLRQ
A
B
3
2
1
/LIWLQJDFFHOHUDWLRQDQGUHWDUGDWLRQPXVWEHNHSW
ZLWKLQVDIHOLPLWVPD[[J
+HOLFRSWHUOLIWLQJLVQRWDOORZHG
%HIRUHUHPRYLQJRLOILOOHUSOXJ )LJ )3 HQVXUH
WKDWWKHSUHVVXUHLVUHOHDVHGE\RSHQLQJDQDLURXWOHW
YDOYH
1
2