Atlas Copco GA 11 VSD Скачать руководство пользователя страница 35

Страница: 35 / 84

‘Service Timer’
‘Running Hours’
‘hrs’

2130

‘Menu’

• The screen shows the actual running hours.
• Press the tabulator key (2): a screen similar to the one below will appear:

‘Service Timer’
‘Level A’
‘hrs’

4000

‘Menu’

‘Mod.’

• The screen indicates that the level for ‘Service Plan’ A is set at 4000 running hours.
• Press the ‘Mod.’ key (F2). The key ‘Lim’ (F2) can be used to find out the limitations for the

parameter. Use the arrow up and arrow down keys to modify the interval.

• Press the ‘Prog’ key (F1) to program the new setting or the ‘Canc’ key (F3) to cancel the

modification operation.

• The procedure to modify the Service plans B, C and D is similar.

3.17 Programming clock function

Control panel

Function

To program:

• Time-based start/stop commands for the compressor
• Time-based change-over commands for the net pressure band

Programming start, stop and pressure band commands

In this example, the compressor will be programmed as follows:

• On Monday at 06:15 starting in ‘Press Band 1’
• On Friday at 18:00 changing over to ‘Press Band 2’
• On Saturday at 18:00 stopping

Instruction book

API161475

Содержание GA 11 VSD





















































































Результаты поиска

Содержание GA 11 VSD

Отзывы:

Бренды по названию

Популярные бренды

Atlas Copco GA 11 VSD, Инструкция

Результаты поиска

Содержание GA 11 VSD

Отзывы:

Бренды по названию

Популярные бренды