Atlanta Attachment Company 1390BX Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 172

background image

Technical Manual & Parts Lists

22

Figure 16

Figure 17

Figure 18

Manual 2

Figure 16

Pressing the arrow button in the upper right corner

of the Manual 1 screen will bring you to the Manual 2
screen. This screen provides controls for the outfeed
conveyors, seal bars, film rollers, mattress roller and size
adjustments.

Setup

Figure 17

Pressing the Setup button on the Main screen will

bring you to the Setup screen. From here you can access
advanced settings, seal setup and advanced manual
controls.

Note: When in the Advanced Manual screen, the

heat to the seal bars is turned off.
Use extreme caution when in Advanced Manual mode.

Setup Seals

Figure 18

Pressing the Seal Setup button on the Setup screen

will bring you to the Setup Seals screen. From this screen
you can change the temperature and the dwell time. You
can also activate the seal bars.

Note: It is recommended that the emergency stop

and power on buttons be used for normal, everyday
machine power up and power down needs. The main
On/Off/Lockout switch should be used to turn the machine
on or off during maintenance or other extended power
down situations.

«
...
28
29
30
31
32
...
»

Содержание 1390BX













































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 1390BX

Бренд: Hagie Страницы: 61

Бренд: JackJaw Страницы: 2

Бренд: Fein Страницы: 248

Бренд: ZF Страницы: 30

Бренд: Raymarine Страницы: 111

Бренд: Modulate Страницы: 2

Бренд: Xebex Fitness Страницы: 15

Бренд: qeedo Страницы: 2

Бренд: Task Force Tips Страницы: 20

DependaBar DB-18-PCW

Бренд: Healthcraft Страницы: 13

IMPULSE 2 IT8026 Glute Master

Бренд: BM FITNESS Страницы: 18

Бренд: Woods Страницы: 54

Бренд: Neilsen Страницы: 8

Бренд: Nektar Страницы: 21

Бренд: Abus Страницы: 2

Бренд: M-system Страницы: 2

Бренд: 2connect Страницы: 8

Бренд: Hakko Electronics Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды