Atlanta Attachment Company 1315A Скачать руководство пользователя | Manualshive

Страница: 13 / 106

background image

Technical Manual & Parts Lists

7

Protect against influences from the surroundings: no structure-borne vibrations, no grinding dust, or
chemical vapors.
Protect against unauthorized access.
Ensure that the machine and accessories are set up in a stable position.
Ensure easy access for operation and maintenance (Instruction Manual and layout diagram); also verify
that the floor is strong enough to carry the weight of the machine.

Local Regulations

Particular attention must be paid to local and statutory regulations, etc. when installing machines and the
plant (e.g. with regard to the specified escape routes). Note the safety zones in relation to adjacent
machines.

Maintenance

General Safety Instructions

The machine shall be switched off, come to a standstill and be secured so that it cannot be switched on
again inadvertently before starting any maintenance work whatsoever. Use proper lockout/tagout
procedures to secure the machine against inadvertent startup.
Remove any oil, grease, dirt and waste from the machine, particularly from the connections and screws,
when starting the maintenance and/or repair work. Do not use any corrosive-cleaning agents. Use lint-
free rags.
Retighten all screw connections that have to be loosened for the maintenance and repair work. Any
safety mechanisms that have to be dismantled for setting-up, maintenance or repair purposes must be
refitted and checked immediately after completing the work.

Maintenance, Care, Adjustment

The activities and intervals specified in the Instruction Manual for carrying out adjustments,
maintenance and inspections must be observed and parts replaced as specified.

All hydraulic and pneumatic lines should be examined for leaks, loose connections, rubbing and damage
whenever the machine is serviced. Any defects found must be remedied immediately.

Waste, Disassembly, Disposal

Waste products should be cleared from the machine as soon as possible as not to create a fire hazard.
Ensure that fuels and operating lubricants, as well as replacement parts are disposed of in a safe and
ecologically acceptable manner. Note the local regulations on pollution control.

When scrapping (disassembling) the machine and its assemblies, ensure that these materials are disposed
of safely. Either commission a specialist company familiar with the local regulations or note the local
regulations when disposing of these materials yourself. Materials should be sorted properly.

From

the

library

of:

Diamond

Needle

Corp

«
...
11
12
13
14
15
...
»

Содержание 1315A











































































































Отзывы:

Нет отзывов

Похожие инструкции для 1315A

Panafax UF-8000

Бренд: Panasonic Страницы: 187

Бренд: Panasonic Страницы: 6

Бренд: Panasonic Страницы: 6

Бренд: Panasonic Страницы: 65

Бренд: Oki Страницы: 16

Бренд: Antari Страницы: 10

Бренд: Republic Bank Страницы: 18

SUPERABRASIVE 13G-X

Бренд: lavina Страницы: 27

Бренд: Taski Страницы: 9

Бренд: Duerkopp Adler Страницы: 78

Бренд: Olivetti Страницы: 130

Бренд: Factory Cat Страницы: 26

Mikasa MVH-200DA

Бренд: MULTIQUIP Страницы: 64

MICROMAG 17'' DISK PAD ASSIST

Бренд: RPS Страницы: 38

Ninja warrior 1200PSI NWCU1312N

Бренд: Prochem Страницы: 44

Бренд: Xerox Страницы: 92

Бренд: Viruserv Страницы: 6

Бренд: Janome Страницы: 43

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды