ATIM Cloud Wireless ACW/LW8-MR4 Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 36

ATIM Cloud Wireless ACW/LW8-MR4 Скачать руководство пользователя страница 18

18

ATIM_ACW-MR4_UG_EN_V1.5

ACW configurator

a.

Compatible configurator version

For an MR4 with the following application software version:

Use the version of ACW Configurator:

Sigfox: V0.0.1

LoRaWAN: V0.0.1

V5.1.0

Download and install the configuration software setup

“

setupACW.exe

”

at:

https://www.atim.com/wp-content/uploads/documentation/CONFIGURATEUR/ACW/configurateur-acw.exe

NOTE

The product

must be in its configuration mode to be detected by the configurator. For safety reasons, configuration is only

possible for 5 minutes after the product has been started. First, the product must be put into deep sleep mode (magnet close
for 6 seconds), wait about 20 seconds for the entry into deep sleep to be effective, then wake up the product (magnet 6 seconds
again). The product can then be configured.

When the ACW Configurator is launched, the waiting
window appears on the screen.

Click on "Help" at the top left of the window then on
"About" to display the version number of the ACW
configurator

Pairing the ACW-MR4 with the configurator can be done in two ways:

•

By USB

: open the case of the ACW-MR4 and connect it to a computer with a micro-USB cable.

•

By Bluetooth

: make sure that Bluetooth is activated.

WARNING

Do not leave the product connected to the configurator (via USB or Bluetooth) unnecessarily, otherwise the autonomy of the
product will be seriously degraded.

«
...
16
17
18
19
20
...
»

Содержание Cloud Wireless ACW/LW8-MR4





































Отзывы:

Нет отзывов