ATI Technologies QC-11 Скачать руководство пользователя страница 72

Manual, Robotic Tool Changer, QC-5 through QC-27
Document #9610-20-2254-09

Pinnacle Park • 1041 Goodworth Drive • Apex, NC 27539 USA • Tel: 919.772.0115 • Fax: 919.772.8259 • 

www.ati-ia.com

 

72

10. Terms and Conditions of Sale

The following Terms and Conditions are a supplement to and include a portion of ATI’s Standard Terms and 

Conditions, which are on file at ATI and available upon request.

ATI warrants to Purchaser that robotic Tool Changer products purchased hereunder will be free from defects 
in material and workmanship under normal use for a period of three (3) years from the date of shipment. This 
warranty does not cover components subject to wear and tear under normal usage or those requiring periodic 
replacement. ATI will have no liability under this warranty unless:  (a) ATI is given written notice of the claimed 
defect and a Description thereof within thirty (30) days after Purchaser discovers the defect and in any event not 

later than the last day of the warranty period; and (b) the defective item is received by ATI not later ten (10) days 

after the last day of the warranty period.  ATI’s entire liability and Purchaser’s sole remedy under this warranty is 
limited to repair or replacement, at ATI’s election, of the defective part or item or, at ATI’s election, refund of the 
price paid for the item.  The foregoing warranty does not apply to any defect or failure resulting from improper 
installation, operation, maintenance or repair by anyone other than ATI.

ATI will in no event be liable for incidental, consequential or special damages of any kind, even if ATI has been 

advised of the possibility of such damages.  ATI’s aggregate liability will in no event exceed the amount paid by 

purchaser for the item which is the subject of claim or dispute.  ATI will have no liability of any kind for failure of 
any equipment or other items not supplied by ATI.  

No action against ATI, regardless of form, arising out of or in any way connected with products or services supplied 
hereunder may be brought more than one (1) year after the cause of action accrued.

No representation or agreement varying or extending the warranty and limitation of remedy provisions contained 

herein is authorized by ATI, and may not be relied upon as having been authorized by ATI, unless in writing and 

signed by an executive officer of ATI.

Unless otherwise agreed in writing by ATI, all designs, drawings, data, inventions, software and other technology 
made or developed by ATI in the course of providing products and services hereunder, and all rights therein under 
any patent, copyright or other law protecting intellectual property, shall be and remain ATI’s property.  The sale of 

products or services hereunder does not convey any express or implied license under any patent, copyright or other 

intellectual property right owned or controlled by ATI, whether relating to the products sold or any other matter 

except for the license expressly granted below.  
In the course of supplying products and services hereunder, ATI may provide or disclose to Purchaser confidential 

and proprietary information of ATI relating to the design, operation or other aspects of ATI’s products.  As between 
ATI and Purchaser, ownership of such information, including without limitation any computer software provided 
to Purchaser by ATI, shall remain in ATI and such information is licensed to Purchaser only for Purchaser’s use in 
operating the products supplied by ATI hereunder in Purchaser’s internal business operations.

Without ATI’s prior written permission, Purchaser will not use such information for any other purpose or provide or 
otherwise make such information available to any third party.  Purchaser agrees to take all reasonable precautions to 

prevent any unauthorized use or disclosure of such information.

Purchaser will not be liable hereunder with respect to disclosure or use of information which:  (a) is in the public 

domain when received from ATI; (b) is thereafter published or otherwise enters the public domain through no fault 

of Purchaser; (c) is in Purchaser’s possession prior to receipt from ATI; (d) is lawfully obtained by Purchaser from a 

third party entitled to disclose it; or (f) is required to be disclosed by judicial order or other governmental authority, 

provided that, with respect to such required disclosures, Purchaser gives ATI prior notice thereof and uses all legally 

available means to maintain the confidentiality of such information.

Содержание QC-11









































































Отзывы: