manualshive.com logo in svg

ATI Technologies FS2, Руководство пользователя, Страница: 13 / 14

Поделиться
Скачать
ATI Technologies FS2 Скачать руководство пользователя страница 13

Manual, Fluid/Air, FS2
Document #9620-20-D-FS2-04

Pinnacle Park • 1031 Goodworth Drive • Apex, NC 27539 • Tel: 919.772.0115 • Fax: 919.772.8259 • 

www.ati-ia.com

 • Email: 

[email protected]

 

D-13

6.  Recommended Spare Parts

Refer to 

Section 8—Drawings

.

Table 6.1—Master Module Mounting Hardware

Part Number

Description

3500-1066020-21A

M6 x 20 Socket Head Cap Screw, SS, ND Microspheres, 0-3 
uncoated lead thds. 5-7 coated thds. IFI525

Table 6.2—Tool Module Mounting Hardware

Part Number

Description

3500-1066016-21A

M6 x 16 Socket Head Cap Screw, SS, ND Microspheres Epoxy, 
Yellow. 0-3 uncoated lead thds. 5-7 coated thds. IFI525

7. 

Specifications

Table 7.1

—Master Module Specifications

Module

Description

Weight

Air Ports, (qty) Size (C

v

)

Pressure 

(Maximum)

9121-FS2-M

Stainless Steel Fluid/

Air module with (4) G1/4 

Checked, (2) G1/4 and (4) 

G1/8 Pass-Thru ports - 

Master

4.56 lbs 
(2.07 kg)

(4) G1/4 (BSPP) (1.50) 
(2) G1/4 (BSPP) (1.03) 
(4) G1/8 (BSPP) (0.65)

100 psi 

(6.9 bar)

Table 7.2

—Tool Module Specifications

Module

Description

Weight

Air Ports, (qty) Size (C

v

)

Pressure 

(Maximum)

9121-FS2-T

Stainless Steel Fluid/

Air module with (4) G1/4 

Checked, (2) G1/4 and (4) 

G1/8 Pass-Thru ports - Tool

4.37 lbs 
(1.98 kg)

(4) G1/4 (BSPP) (1.50) 
(2) G1/4 (BSPP) (1.03) 
(4) G1/8 (BSPP) (0.65)

100 psi 

(6.9 bar)

Содержание FS2















Отзывы:

Нет отзывов