ATI Technologies 9105-NET-Axia80-M20-ZC22 Скачать руководство пользователя страница 37

Страница: 37 / 94

Manual, F/T Sensor, Ethernet Axia
Document #9610-05-Ethernet Axia-09

Pinnacle Park • 1031 Goodworth Drive • Apex, NC 27539 • Tel:+1 919.772.0115 • Fax:+1 919.772.8259 •

www.ati-ia.com

4.8.2 How to Interpret Hexadecimal Output for the Status Code

The user converts hexadecimals to a 32-bit binary number that correlates to a status code from

Table 4.7

. An example of bit patterns are in the following table.

Table 4.9—Bit Pattern Examples

Bit Number

Simple Description
(refer to

Table 4.7

)

Bit Pattern

Temperature

0x80000001

Supply voltage

0x80000002

Broken gage

0x80000004

Busy bit

0x80000008

Reserved

N/A

Other

0x80000020

6 to 15

Reserved

N/A

Monitor condition latched

0x00010000

17 to 26

Reserved

N/A

Gage out of range

0x88000000

Simulated error

0x10000000

Calibration checksum error

0xA0000000

F/T out of range

0xC0000000

Any error

0x80000000

Healthy

0x00000000

The bit pattern can be different if more than one error is present. For example, a user issues

this console command (refer to

Section 8.3—Secondary Commands for the Query “c”

or “s” Command

user:

s !

response:

80000005

Using a free online calculator, convert the hexadecimal number to a binary number:

Hex

Binary

1000

0000

0101

The binary number has 32-bits total. The least significant bit is on the right end of the following

table. “1” means the bit is on. “0” means the bit is off.

Binary

Number

000 0000 0000 0000 0000 00

Bit

Position

26 to 6

So in this example, bit number 0, 2 and 31 are on. According to the preceding table, the sensor has

a “temperature”, “broken gage error”, and “any error” status codes (refer to

Table 4.7

Содержание 9105-NET-Axia80-M20-ZC22































































































Результаты поиска

Содержание 9105-NET-Axia80-M20-ZC22

Отзывы:

ATI Technologies 9105-NET-Axia80-M20-ZC22, Руководство пользователя, Страница: 37 / 94

Результаты поиска

Содержание 9105-NET-Axia80-M20-ZC22

Отзывы: