ATH HEATNET KN Series Скачать руководство пользователя страница 79 | Manualshive

Страница: 79 / 144

ATH HEATNET KN Series Скачать руководство пользователя страница 79

OPTIONAL FEATURES

HeatNet Control V3 3.x

Page 79

HeatNet Online

HeatNet Online is a web-based system for fault
notification, monitoring and tuning of a HeatNet based
system. A HeatNet Online bridge module is required to
connect a boiler (Usually the MASTER boiler) to the
internet. The bridge is available for version 2.x and version
3.x HeatNet controls that do not have a touchscreen
display.

If the boiler is so equipped, the touchscreen display
provides an RJ45 connection for access to the internet.

Shown below, the network connection resides on the upper
left corner of the display. If an RJ45 hardline is not
available, a wireless modem can also be used. Consult the
factory or sales for available solutions.

The HeatNet Online site may be accessed at:

www.heatnet.net/

. A login Account/Password is required.

For set-up information follow the “LCD Touchscreen
HeatNet Online Setup Instructions” available in the
Technical Library on the KN-Series website.
(

www.knseries.com

Once a user has registered a site, the user’s email can be set
up to provide daily status messages and fault/alarm emails
within minutes of trouble. This provides a valuable tool for
technicians on the road. If the technician has a smart phone,
they can be notified through the emails on their phone.
They can then log on to the HeatNet Online website (from
their phone) to determine the trouble. Sample email
message:

HeatNet Online Alert

Church St

–

Address and building location displayed here

Church Street Heat - Basement

M (MB
750)

Fault

High
Limit

May 17 2014
11:09AM

WVHID99999

View Alert
Data

A selection screen for the building sites, that the user has
registered, will be displayed after the user has logged in.
When a building site is selected, the main Live screen will
be entered. This is the HOME screen and provides a quick
view on the status of the site.

Selecting the History tab allows a runtime Histogram of the
System. The histogram displays temperatures and states of
the system in a date/time format. Also displayed is the
MASTER boiler log, faults, messages, modulation, and
events. To the right of the histogram is the MASTER
Boiler’s log. Since the HeatNet bridge only transmits at 1-
minute intervals, the log can be used to precisely view the
state of the boiler at the time of the event (in-between
minutes).

«
...
77
78
79
80
81
...
»

Содержание HEATNET KN Series

















































































































































Отзывы:

Нет отзывов