ATH HEATNET KN Series Скачать руководство пользователя страница 68 | Manualshive

Страница: 68 / 144

ATH HEATNET KN Series Скачать руководство пользователя страница 68

OPTIONAL FEATURES

HeatNet Control V3 3.x

Page 68

The Stack sensor should be a 1k ohm platinum type sensor.
Part # 0040-1300. To configure the 1k PT Stack sensor,
Switch S5.3 should be set to the NONE position and S5.4 set
to PLATINUM STACK. The sensor will then be auto
detected after a power cycle.

Security

A password can be used to lock out control and setup features.
It can be enabled but is shipped in the disabled state.

USB Features

The HeatNet V3 control supports a USB updating system and
desktop connectivity using the HeatNet Control Pro software.

In order to ensure that a valid firmware file is always
available on the HeatNet board, (2) file storage locations are
available. A firmware file is loaded at the factory in both
locations. This is to ensure that if a bad file is loaded by the
user, the factory loaded file can be re-loaded to get the board
functional again. All updating of firmware or Display
applications use the front panel USB input.

The firmware loading menu is located at; SETTINGS: LOAD
DISPLAY FIRMWARE & SETTINGS: LOAD CONTROL
FIRMWARE. The following explains the menus.

Loading the Display Firmware

Selecting the LOAD DISPLAY FIRMWARE menu allows
updating the displays application program which resides on
the display. This does not update the controls firmware. New
firmware is posted periodically on Sales Assistant or the KN
website.

Navigate to page 4 of 4 in the settings menu and select “Load
Display Firmware”.

Select the (Select File) … box to view the drive.

The thumb drive will appear as a folder. Select the folder and
you will see the files in that folder.

«
...
66
67
68
69
70
...
»

Содержание HEATNET KN Series

















































































































































Отзывы:

Нет отзывов