ATH-Heinl ATH-CROSS LIFT 50 Скачать руководство пользователя страница 12

Страница: 12 / 84

Type

ATH ATH-CROSS LIFT 50

Capacity main lift

5.000 kg

Capacity freewheel lift

4.000 kg

Lifting time (at 2.000 kg)

70 s

Lowering time (at 2.000 kg)

60 s

Electrical system

3/400V/50Hz

Voltage

DC24V

Motor

3,5 KW

rpm

1375

Motor housing

B14

Fuse protection

3 C 16 A

Connection cable

Min. 5 x 2,5m²

Protection class

IP 54

Flow rate

4,8 cm³/g

Working pressure ²

230 -240 bar (max. 250 bar)

Needed compressed air connection

7 bar

Recommended hydraulic oil

Summer: H-LPD 32 (e.g.: OEST H-LPD 32 DD L)

Winter: H-LPD 22

Oil volume

appr. 18 l

Anchoring on the floor

Anchor bolts: M16 x 180 (z.B.: Atrion ABL-W 16-060-180)

Chemical anchor: M16 x 190 (z.B.: Atrion AVA-W 16-045-190)

Anchor amount

16 pieces

Admitted noise level

≤ 80 dB

Weight

2.840 kg

The already factory-set working pressure is adjusted tot he maximum rating. The setting of the pressure control

valve may not be changed. Any changes to the setting can cause serious damages.
If the nominal load cannot be lifted please contact our service team.

Scope of delivery

Basic package with:

•

Both scissor pairs incl. installed cylinders

Switching box with:

•

Installed hydraulic unit

•

Hydraulic hoses

•

Air hoses

•

Rubber pads

•

Technical documents

Two cover plates

Two drive-on ramps with four covers for connections between scissors and switching box

OPTIONAL
Rolling jack

If anything is missing in scope of delivery please contact our sales department.

Instructions for transport and storage:
-

Lift carefully, support the load by using suitable means of support in perfect working condition.

Avoid sudden jolts and tugs, watch out for uneven surfaces, bumps etc.

After removing the packing, check that they are taken to special waste collecting areas inaccesible to children and
animals as long as they are not disposed.

Storage temperature: -10

℃

～

+40 °C

Содержание ATH-CROSS LIFT 50


























































Результаты поиска

Содержание ATH-CROSS LIFT 50

Отзывы:

Похожие инструкции для ATH-CROSS LIFT 50

Бренды по названию

Популярные бренды

ATH-Heinl ATH-CROSS LIFT 50, Руководство пользователя

Результаты поиска

Содержание ATH-CROSS LIFT 50

Отзывы:

Похожие инструкции для ATH-CROSS LIFT 50

Бренды по названию

Популярные бренды