ATEN VM5404HA Скачать руководство пользователя страница 93

Страница: 93 / 122

Chapter 4. Browser Operation

Editing a User Account

1. Log in the VM5404HA / VM5808HA web interface using an

administrator account.

2. Go to

Settings

Maintenance

User Account

. A list of created accounts

appears.

3. Click

Edit

to edit account settings as needed.

Network Settings

You can configure the VM5404HA / VM5808HA’s network settings, such as
connection mode (DHCP or fixed IP address), IP address for the web console,
and Telnet connection.

To configure the system network settings, do the following:

1. In the VM5404HA / VM5808HA web interface, go to

Settings

Maintenance

Network

. This page appears.

2. Configure the settings as needed.



DHCP



Enable

– Select this option to allow the DHCP server to

automatically assign an IP address to the VM5404HA /
VM5808HA.



Disable

– Select this option to assign a static IP address for the

device.

Содержание VM5404HA



























































































































Результаты поиска

Содержание VM5404HA

Отзывы:

Похожие инструкции для VM5404HA

Бренды по названию

Популярные бренды

ATEN VM5404HA, Руководство пользователя

Результаты поиска

Содержание VM5404HA

Отзывы:

Похожие инструкции для VM5404HA

Бренды по названию

Популярные бренды