background image

15

Chapter 3

Front Panel Operation

Overview

The VM0808H can be configured and operated locally from the front panel via 
the LCD using the built-in tuner dials, pushbuttons and the IR Remote Control.

It can also be controlled remotely over a standard TCP/IP connection via 
graphical user interface (GUI) using a web browser; or by a RS-232 serial 
controller. 

The local front panel operation is discussed in this chapter, while Over-IP 
operation is discussed in Chapter 4, and RS-232 serial control is discussed in 
Chapter 5. 

Front Panel Pushbuttons

The VM0808H front panel features an LCD display, tuner dials and 
pushbuttons for convenient configuration and operation locally. This allows 
users to perform operations such as selecting which source shows on which 
display, configuring the IP port, configuring the serial port, setting Power On 
Detection and EDID modes, selecting security settings, and loading/saving 
connection profiles.

The VM0808H’s front panel display operation is easy and convenient. Note the 
following front panel pushbutton functions:

Š

Use the 

MENU

 pushbutton to access the Menu page options: Set IP Port, 

Set Serial Port, Operation Mode, Security Mode, and Save/Load Profile 
(see 

Menu Organization

, page 18)

Š

Use the 

PROFILE

 pushbutton to switch between the connection profiles 

which have been added to the Profile Selection list (see 

Profile 

Pushbutton

, page 29 and 

Profile Selection

, page 42)

Š

Use the 

ESC

 pushbutton to go back a level, return to the Main screen, or 

exit the page/screen

Š

Use the 

ENTER

 or tuner dial pushbuttons to select options and confirm 

operations

Š

Use the 

IN

 and 

OUT

 tuner dials to cycle forward or backward through the 

submenus or options

Содержание VM0808H















































































Отзывы: